Model # OCR19X C1

Internet #202047058

Store SKU #235674

null 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve
0026613135786

1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve

  • Controls water flow to household plumbing fixtures
  • For use with faucets, toilets, dishwashers and icemakers
  • Easy repair without shutting off the water to your home
$787 /each
store icon Loading Buying Options...
package icon Loading Buying Options...
Sorry, but we ran into issues loading these options. Please try refreshing.

Frequently Bought Together

Product Overview

  • Controls water flow to household plumbing fixtures
  • For use with faucets, toilets, dishwashers and icemakers
  • Easy repair without shutting off the water to your home
BrassCraft 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve controls water flow to household plumbing fixtures - faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a few turns of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without turning off water to the entire home.
  • Compatible with copper or PEX (PEX installations require a stainless steel tube insert)
  • Machined, 1-piece body construction for strength, durability and long-lasting performance
  • Easy-to-remove handle protects against accidental operation during rough-ins
  • Multi-turn operation means water flow control with only a few turns of the handle
  • Oval-knurled handle provides a secure grip for on/off operation
  • Chrome-plated brass
  • Temperature rating: 40 Degree to 140 Degree
  • Pressure rating: 125 psi maximum
  • No-lead certified
  • IAPMO and CSA listed to ASME A112.18.1/CSA B125.1

Product Overview

  • Controls water flow to household plumbing fixtures
  • For use with faucets, toilets, dishwashers and icemakers
  • Easy repair without shutting off the water to your home
Model #: OCR19X C1
Sku #: 235674
Internet #: 202047058

BrassCraft 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve controls water flow to household plumbing fixtures - faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a few turns of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without turning off water to the entire home.

  • Compatible with copper or PEX (PEX installations require a stainless steel tube insert)
  • Machined, 1-piece body construction for strength, durability and long-lasting performance
  • Easy-to-remove handle protects against accidental operation during rough-ins
  • Multi-turn operation means water flow control with only a few turns of the handle
  • Oval-knurled handle provides a secure grip for on/off operation
  • Chrome-plated brass
  • Temperature rating: 40 Degree to 140 Degree
  • Pressure rating: 125 psi maximum
  • No-lead certified
  • IAPMO and CSA listed to ASME A112.18.1/CSA B125.1

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.

Customers Also Compared These

Price
$7.87 /each
$8.97 /each
$9.72 /each
$9.72 /each
Name 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Angle Valve 1/2 in. Nominal Push Connect Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Angle Valve 1/2 in. Chrome-Plated Brass Push-to-Connect x 3/8 in. O.D. Compression Quarter-Turn Angle Stop Valve
Brand BrassCraft BrassCraft SharkBite
Ratings (24) (69) (4) (49)
Valve Outlet Diameter (in.) .375 0.375 .375 0.375
Valve Inlet Diameter (in.) .5 0.5 .500 0.5
Connection Comp x Comp Comp x Comp PTC x Comp PTC x Comp
View Product View Product View Product View Product

Specifications

Dimensions

Product Height (in.)
2.75
Product Length (in.)
2.75 in
Product Width (in.)
2.25
Valve Inlet Diameter (in.)
.5
Valve Outlet Diameter (in.)
.375

Details

Compatible Pipe Material
Copper
Connection
Comp x Comp
Indoor/Outdoor
Indoor,Outdoor
Material
Brass
Maximum Pressure (psi)
125
Maximum Working Temperature (F)
140
Product Weight (lb.)
.20611lb
Returnable
90-Day
Valve Type
Stop

Warranty / Certifications

Manufacturer Warranty
Limited Manufacturer Warranty

Specifications

Dimensions

Product Height (in.)
2.75
Product Length (in.)
2.75 in
Product Width (in.)
2.25
Valve Inlet Diameter (in.)
.5
Valve Outlet Diameter (in.)
.375

Details

Compatible Pipe Material
Copper
Connection
Comp x Comp
Indoor/Outdoor
Indoor,Outdoor
Material
Brass
Maximum Pressure (psi)
125
Maximum Working Temperature (F)
140
Product Weight (lb.)
.20611lb
Returnable
90-Day
Valve Type
Stop

Warranty / Certifications

Manufacturer Warranty
Limited Manufacturer Warranty

Questions & Answers

my replacement shut off valves are leaking how do I stop the leak?

I have copper lines coming out of the wall with nut and a compression washer that has the shut off valve screwed into it. The old valves had to be replaced so i bought new valves put the white tape on the threads screwed them in but they leaked. I have repeated the process a few times but no success. What must I do to stop the leak?
Asked by: mzone45
1) Compression fittings do not get tape put on them. The seal is accomplished by compressing the ring or ferrule thru tightening of the nut, in effect squishing the ring around the pipe. Gently try to tighten the nut. It is critical to avoid over-tightening the nut or else the integrity of the compression fitting will be compromised by the excessive force. If the nut is overtightened the ferrule will deform improperly causing the joint to fail. A good rule of thumb is to tighten the nut first by hand until it is too difficult to continue and then tighten the nut one half-turn more with the aid of a wrench; the actual amount varies with the size of the fitting, as a larger one requires less tightening. The fitting is then tested: if slight weeping is observed, the fitting is gradually tightened until the weeping stops.
Answered by: wn6wtv
Date published: 2017-12-31

can we connect this valve whit cpvc male adapter 187739?

Asked by: famrod1
This valve uses a compression sleeve to connect to a half-inch copper line. This adapter you're asking about is for 3/4" line. I don't believe the OD size of CPVC and copper are the same, and even if-so, would probably not hold pressure without blowing-off causing serious damage. There are adapters available, but CPVC is necessary only for hot-water, otherwise PVC should work well. I would look-for a 1/2" PVC to compression adapter.
Answered by: richy
Date published: 2017-11-08

All of a sudden my toilet leaks, I go to turn the water off and it wont, even with the knob turned off will replacing th

Asked by: Chell
Whole house flow must be turned off at the meter, and this valve then replaced. It's known as a "stop" valve.
Answered by: richy
Date published: 2017-12-31

I need to replace the washer as my valve won't shut off. What size washer should I buy?

I need to replace the washer as my valve won't shut off. What size washer should I buy?
Asked by: SPG
Danco 88569 washer in home depot. OD 1/2 in, ID ~3/16 in. "If I need a pair of shoes, I am not going to buy a collect from size 6 to size 14"
Answered by: Dz
Date published: 2017-12-05
  • y_2018, m_1, d_17, h_13CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_, sid_202047058, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 121ms
  • QUESTIONS, PRODUCT

Customer Reviews

1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet Multi-Turn Angle Valve is rated 4.4 out of 5 by 24.
Rated 2 out of 5 by from I had hoped to procure 1/4 turn valves and NOT "multi-turn" valves. The 1/4 turn valves are BALL ... I had hoped to procure 1/4 turn valves and NOT "multi-turn" valves. The 1/4 turn valves are BALL valves and not "stem and seat" valves. Stem and seat valve design is from the 1930's, and I regard them as junk. Over the years, I have had almost all of these type valves fail, with erosion on the seat, stem screw and washer failure. Ball-types with simple design and switch-like actuation are MUCH superior. These multi-turn valves should be removed from stock, as they promote water-waste, and are almost impossible to repair.
Date published: 2017-11-08
Rated 5 out of 5 by from Excellent replacement valve. Very easy to install. Operates with little effort. No leaks when don... Excellent replacement valve. Very easy to install. Operates with little effort. No leaks when done. Good valve at a good price.
Date published: 2017-12-03
Rated 5 out of 5 by from Great product, appears to be same build quality as the... Great product, appears to be same build quality as the 12 yr. old original. Thanks Steve
Date published: 2017-08-29
Rated 5 out of 5 by from Perfect for the tight application I used this valve with. Perfect for the tight application I used this valve with.
Date published: 2017-09-19
Rated 4 out of 5 by from Doesn't leak that's all I care. Easy install. ... Doesn't leak that's all I care. Easy install.
Date published: 2017-09-05
Rated 5 out of 5 by from 5 Star Review Rating provided by a verified purchaser
Date published: 2017-10-28
Rated 1 out of 5 by from Poor Seal Like many HD products, this one is a low cost import. Fine. Imports are OK. BUT, the valve fails to seat properly after just a few uses v.v. won't shut off water flow fully when turned to 100% off. Given the time and hassle required to replace a valve, one would want it to last ... this product DOES NOT LAST. And, this view isn't just about one valve but based on experience with 3. These valves won't last.
Date published: 2016-07-06
Rated 5 out of 5 by from Easy Install While remodeling my guest bathroom, I noticed the old valve beginning to leak (it's 33 years old). This was an easy replacement for the old. Just remember to have a clean straight edge to install.
Date published: 2016-08-29
  • y_2018, m_1, d_18, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_24
  • loc_, sid_202047058, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 112ms
  • REVIEWS, PRODUCT