#1 Home Improvement Retailer

4 in. Aluminum 90-Degree Elbow

$658
  • Adjustable from 0 to 90 degrees in bend
  • Constructed of corrosion proof aluminum
  • Easily install with one crimped end
  • View More Details
Store
0 in stock
caret

Product Details

This all aluminum elbow has a 4-piece construction and can be adjusted up to 90 to use at various angles. It can be used in many general-purpose applications including the venting of most types of heating units. The aluminum elbow has 1-crimped end and 1-straight end.

Additional Resources

From the Manufacturer

caret

Specifications

caret

Questions & Answers

5Questions
caret
Q:I need one just a bit longer for my dryer
by|Sep 11, 2022
1 Answer
Answer This Question

A:  This is the only length this product comes in. You can purchase a 4" aluminum duct connector that will insert into your dryer exhaust port and extend that exhaust port so you can then attach an elbow to it. https://www.homedepot.com/p/Everbilt-4-in-x-4-in-Solid-Aluminum-Duct-Connector-FDC4XHD8/203626505

by|Sep 12, 2022
    caret
    Q:I need 13 5/8 square duct and a 90 degree elbow to connect my swamp cooler, preferably aluminum
    by|Aug 12, 2021
    1 Answer
    Answer This Question

    A:  This ducting is not sold in the Everbilt dryer venting category at Home Depot

    by|Aug 20, 2021
      caret
      Q:North Carolina building code specify's 28 gauge Aluminum or 26 gauge galvanized metal duct @ 4" d...
      by|May 21, 2021
      1 Answer
      Answer This Question

      A:  You should always follow you rlocal building code requirements as they vary from state to state. However, in general, these products are not made of 28 gaugae aluminum and do not have an indeed use for "in-wall" applications which is what this code indicates. These elbows are used in "transition" areas for flex duct not inside a wall cavity.

      by|May 27, 2021
        caret
        Q:what gauge is this?
        by|Oct 17, 2018
        1 Answer
        Answer This Question

        A:  Thickness is .011 and 30 is the gauge.

        by|May 21, 2021
          2 found this answer helpful
          Showing 1-4 of 5
          caret

          Customer Reviews

          3.2 out of 5
          (246)
          • 3.2
            out of 246 reviews
          • 44% recommend this product
          Filter by:
          Showing 1-10 of 246 reviews
          This item byself (elbow) became separate
          Last long only for 1 day (24 hours) elbow byself came separate from each rings.. poor low quality material
          by
            Extended Dryer Vent
            It worked as designed. Just be careful, in the past I’ve had fittings like this come apart and they are not repairable. These however did just fine.
            by
            • Verified Purchase
            • Recommended
            Flimsy.. use 3M tape to hold it together
            The fitting came apart when fitting.. I bad to tape it together.. flimsy
            by
            • Verified Purchase
            Not the Everbilt 4 in. 90° aluminium elbow of past
            The current HD offering for 4 in. 90° elbow has little to do in quality and gauge with their earlier product. Will need to carefully tape the new elbow to prevent leaks from all the joints.
            by
              This is a four-inch diameter elbow which is of a typical design found in HVAC ducting. I do appre...
              This is a four-inch diameter elbow which is of a typical design found in HVAC ducting. I do appreciate that each segment swivels, allowing a lot of flexibility in adjusting the elbow to different angles, including compounded curves for tricky areas. It seems that this is the only type of elbow Home Depot carries, which is perfectly acceptable to me. Note that this part is aluminum while most HVAC ducting parts are sheet metal steel, and you notice this right away considering how light this item is. I'm not sure how significant the difference is, just note that it is of a different material than is what is typically used in HVAC installations.
              by
              • Recommended
              1 found this review helpful
              I received the EVERBILT 4 IN. ALUMINUM 90-DEGREE ELBOW, SILVER to test for Home Depot. I used i...
              I received the EVERBILT 4 IN. ALUMINUM 90-DEGREE ELBOW, SILVER to test for Home Depot. I used it to replace my existing dryer vent. It was easy to assemble. I wish it was a heavier gauge metal though. It think that it will be fine as I not using it for heating or cooling. I felt like I should tape the seams to insure that I didn't get lint in the laundry area. I also used the EVERBILT 4 IN. X 2 FT. ALUMINUM PIPE, SILVER to complete the installation.
              by
              • Recommended
              1 found this review helpful
              This is about the same guage and durability of other aluminum ducting that you'll use for dryers....
              This is about the same guage and durability of other aluminum ducting that you'll use for dryers. It was easy to adjust the angle and I was able to secure it with 4" worm gear clamps without crushing the duct. One end is tapered as expected. There didn't seem to be any leaks coming out of the sections but out of an abundance of caution, I would tape the seams using foil tape. An ounce of prevention and all that.
              by
              • Recommended
              2 found this review helpful
              Not just 90 degrees, lots of possible angles. This elbow consists of four sections and three joi...
              Not just 90 degrees, lots of possible angles. This elbow consists of four sections and three joints that swivel. This adds a lot of flexibility for your application. The material is sturdy, even when swiveled into various angles. This would be ideal to install at the end of a dryer vent run rather than use a flexible dryer hose. Much sturdier than the semi-rigid dryer vents.
              by
              • Recommended
              2 found this review helpful
              This elbow is easy to reconfigure and will stay in that configuration. The joints are closely ben...
              This elbow is easy to reconfigure and will stay in that configuration. The joints are closely bent to stay together and to move easily. The fitting fits well in dryer exhaust hose. This fitting is nice to use if the two points are not quite correct this fitting can be adjusted to correct the off set. Being made from aluminum it is light weight and can be installed overhead.
              by
              • Recommended
              3 found this review helpful
              Before we even got to use it, it broke and was impossible to reattach
              by
                Showing 1-10 of 246 reviews

                Compare Similar Grow Room Ventilation

                Exclusive4 in. x 2 ft. Aluminum Pipe
                current product
                Exclusive4 in. Aluminum 90-Degree Elbow
                Exclusive4 in. Draft BlockerTop Rated4 in. x 8 ft. Flexible Aluminum Dryer Vent Duct
                BrandEverbiltEverbiltEverbiltEverbilt
                Name4 in. x 2 ft. Aluminum Pipe4 in. Aluminum 90-Degree Elbow4 in. Draft Blocker4 in. x 8 ft. Flexible Aluminum Dryer Vent Duct
                Price
                $598
                $658
                $942
                $1428
                Ratings
                (97)
                (241)
                (137)
                (326)
                InsulatedNoNoNoNo
                Maximum air flow (CFM)0000
                View ProductView ProductView ProductView Product