10 ft. x 36 in. 240-Volt Radiant Floor Heating System for Laminate, Vinyl, and Floating Floors (Covers 30 sq. ft.)

Excellent for dry areas. Not recommended for wet zones.

I put 7 of these heating mats under my new family room laminate floor. The mats have a little curl to them from packaging but I put the curl facing down which worked out fine. Running all the wires took a little time as they have fit into your underlayment not just lay on top of it but overall the installation went very smooth. These mats work great, my wife and daughters love how the floors feel to their feet.

So worth the money!! I would rate 6stars if i could, having warm floors is the best. We had an electrician hook them up to the thermostat and test them, but did the rest of the installation ourselves.

Really easy. It is thin and cuts easily. The warm fllors feel great. Still tweaking the thermostat, is set at 70 for four hours in the morning, but my thermometer says the floor is 88 to 90. Thermostat could be a little easier to use. Install it at eye level in good light.

Game changer. Easy to install, goes under luxury vinyl tile, or wood, or Pergo. Easy to cut. Thin. Great thermostat, easy to program. The warmth under your feet coming out of the shower is priceless. Only person unhappy about it is my wife, because it was installed in my bathroom and not hers.

The receipt of this product led to a complete remodel of our bathroom. That is why the review took so long to publish. Saying that the thin film floor heating element works fine. The very nice feeling when you walk into the bathroom barefoot and the floor is warm. I installed the heating film under Snap Stone tile over the old vinyl tile floor. The purchase of a GFCI protected thermostat was also necessary for the installation to function properly. So QuietWarmth is the new way to have heated floors without a lot of extra construction.

Great stand alone product, to augment your heating, for somewhere you might sit a long time (e.g. a desk or in front of a TV couch) or have bare feet touching the floor (e.g. next to a bed or in a bathroom), but if you move the desk/couch/bed, you will have to rip up the floor to move it along. The directions show you being able to set up a grid of these, to heat an entire room's floor, but I am not sure how cost effective that would be? The box states, 'Heat your floor for pennies a day!', but just this one alone uses 334W. Three hours of use, and you have used a Kilowatt. My Power Company charges me $.18/Kilowatt. Multiple that by hours run per day, and multiple that by numerous mats ... and it is more like 'dollars a day' (imho). I also find it odd, and a much larger installation expense, to require this be on a 'dedicated' 20A breaker (i.e. run 12 gauge wire from this to the breaker box). It uses less than 3A. Running this to the closest outlet, and upgrading that outlet to GFI, seems sufficient. A dedicated 20A would make sense if you ganged 5 of these. Only had it a few days, and like it so far. Have not got a power bill. but time will tell ... Best part, which I do not see mentioned anywhere, it is stamped, 'Made in USA'

The Quiet Warmth Radiant Heat film for FLOATING FLOORS is a must in the winter months in Michigan! This particular heat film is for Floating Floors only so be careful when choosing which kind you want. I am installing a floating tile which snaps together and then you apply a special floating tile grout. See pictures. The thermostat is sold separately and you will need a DEDICATED 20 amp circuit which is protected by a GFCI. The technical hotline is 1-888-WARMPAD in case you need to clarify anything before you buy this. You totally control the floor heating with the thermostat which attaches to the wiring on the pad and is wired up the wall of the room you're installing this in. If you are installing this heated film in a basement on concrete, you will need to install a 6-mil vapor barrier (underlayment) on top of a subfloor before laying the heat film and then the floating floor. Again, I chose to put down a floating tile but you can use other floating floors such as laminate or engineered wood. Make sure that whatever floor you decide on, that you check to make sure it is rated for use with electric floor warming systems. I had an electrician lay this film because I wanted to make sure it was wired correctly before laying the tile flooring and grout! Some things needed from electrician are 2 junction boxes (3" for thermostat and 4" for electrical connections along with 12/2 Romex Wire. I did not need a separate GFCI because my thermostat had an integrated one.(see picture). This was a pretty simple installation for my electrician because I wasn't attaching other heated film matts to each other. This was for a bathroom in which my 10' x 3' size was sufficient. I love the ability to turn it on and have a warm floor to walk on when I get out of the shower!

Just in time for our new wood floor in our walk in closet. The product was easy to install but you do need lots of planning. The actual install was fast but you do need to read and understand the electrical,requirements that will also go through a thermostat not included . First you need a 20 amp circuit that is not shared. Then you need to get the wires to the radiant heat film. Remember this is Radiant heat film and is not instant heat it could take from hours to days to get your floor area up to your desired temperature . Depending on the sub floor and the floor finish will determine the amount of time . Radiant heat takes a while for things to absorb the energy the air in most cases may never reach your desired temp. It is also something you don't turn off and i.e. peck it ti cool quickly. So great product made well with high quality products. Not a beginner project but can be done , read the instructions and hire an electrician if electric is not your thing.

This is a luxurious yet affordable upgade, especially if you are planning on putting in new floors anyway. There are videos to help with installation. I have minimal experience working with electrical projects, but by reading the instructions and watching the helpful videos, I was able to install the necessary junction box, thermostat, and run the wires from 2 heating mats to the thermostat in an existing home where we were redoing the floors. It is helpful to install an underlayment barrier under the Quiet Warmth roll; that way you can cut channels into the underlayment where the wires run across the floor to the wall where the thermostat is installed. Otherwise the wires, though they are small, might be felt under the flooring (we put in luxury vinyl planks; wires might not be as noticeable under harder wood or laminate.) These rolls are super easy to cut with sharp scissors to get them just the right size for your project. Once installed, use the thermostat to control the temperature; the rolls give off a nice warm touch from the floor, removing the chill, and help to keep the room they are installed in warmer. We are very happy with them.