Internet #100111743

Model #7200-11C

Store SKU #568582

Store SO SKU #1001375102

11 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube

  • Acrylic base formula for extremely convenient setup
  • Anti-microbial protection to prevent growth of bacteria and mold
  • Packaged in cartridge tubes for convenient application
  • See More Details

Frequently Bought Together

+
+
Price:
$415

Product Overview

ROBERTS 7200 Wall Base Adhesive is a superior grade, solvent free and zero Volatile Organic Compound (VOC) product with excellent holding power and great wet suction. This acrylic base formula is non-staining for easy cleanup, features a strong initial grab for fast installation and is odorless when dry. This adhesive meets the strict requirements of the South Coast Air Quality Management District and may contribute one LEED point as a low emitting adhesive.
  • For the installation of vinyl, rubber and carpet wall base
  • Bonds with porous wall surfaces such as gypsum drywall, plaster, brick, and concrete block
  • Non-staining formula for easier cleanup
  • Formulated for quick grab and rapid set-up for fast, easy installation
  • Up to 10 minutes open time, up to 30 minutes working time and 24 to 48 hours curing time
  • For a 4 in. wall base, coverage is approximately 18 to 22 linear feet per 11 ounces
  • Install with a ROBERTS snozzle and caulking gun
  • Enviro-friendly, solvent-free and LEED compliant; VOC < 1 g/L, SCAQMD Rule 1168
  • Protected by GoldGuard, an antimicrobial protection system that inhibits the growth of mold, mildew and odor causing bacteria in both wet and dry adhesives
  • CRI Green Label Plus Certified - GLP no.71129
  • 1 year limited warranty
  • Not recommended for use in wet areas

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.

Compare Similar Vinyl Adhesives

current product
11 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube
440 30 oz. Cove Base Adhesive2001 1 Qt. Felt-Backed Sheet Vinyl Flooring Adhesive1 Qt. Vinyl Composition Tile Floor Adhesive
BrandRobertsHenryRobertsRoberts
Name11 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube440 30 oz. Cove Base Adhesive2001 1 Qt. Felt-Backed Sheet Vinyl Flooring Adhesive1 Qt. Vinyl Composition Tile Floor Adhesive
Price
$415
$536
$5.96
Save 60¢ (10%)
$622
$798
Ratings
(150)
(8)
(186)
(546)
Maximum coverage area (sq. ft.)7.5804847
Flooring Material FeaturesSolvent freeLatex based,Solvent free,Water basedLatex based,Solvent freeLatex based,Solvent free
LocationInterior wallFloor,Interior wallFloorFloor
Flooring TypeVinylVinylVinylVinyl
Flooring Product TypeVinyl AdhesiveVinyl AdhesiveVinyl AdhesiveVinyl Adhesive
View ProductView ProductView ProductView Product

Specifications

Dimensions

Container size (qt.)
0.34375
Maximum coverage area (sq. ft.)
7.5
Product Width (in.)
2

Details

Adhesive Type
Vinyl
Color Family
Beige
Commercial / Residential
Commercial / Residential
Dry time (hours)
24
Flooring Material Features
Solvent free
Flooring Product Type
Vinyl Adhesive
Flooring Type
Vinyl
Indoor/Outdoor
Indoor
Location
Interior wall
Product Weight (lb.)
1
Returnable
180-Day

Warranty / Certifications

Lifetime Warranty
No
Manufacturer Warranty
To be free from manufacturing defects

Questions & Answers

66Questions15Answers

aside from contact cement, is there an adhesive that can be used to apply laminate to a wall surf...

Asked by Joseph January 29, 2021
1
Answer

Always follow the floor manufacturers' specific vertical application guidelines. ROBERTS 7200 is a superior performing wall base adhesive with exceptional wet grab and rapid set-up for the fast installation of wall base and is Not recommended for your project needs.

Will this product stick to stainless steel?

Asked by Jim January 27, 2021
1
Answer

No, ROBERTS 7200 is not recommended over nonporous or painted surfaces.

Bubbles the size of dessert plates have come up under my 2 year old sheet vinyl flooring. Would t...

Asked by bubbleblues September 22, 2020
2
Answers

No, 7200 is specific to Cove Base applications. Roberts 2310 can potentially be used to re-adhere the flooring. Discovering the reason behind the bubbles is key to resolving the issue. Bubbles can appear under vinyl sheet flooring when moisture or moist air rises from below. Either one of these components becomes trapped between substrate and the vinyl creating a bubble or a warp in the subfloor surface. Bubbles can appear following a high moisture event. (maintenance, plumbing leaks, excess rain, w/ poor drainage etc.)

Is this suitable for installing vinyl cove base in a garage (in Texas)?

Asked by Alaks September 19, 2020
2
Answers

Roberts 7200 is specifically warranted for Interior (controlled environments) applications. However, Depending on the Garage ambient condition, installation is plausible: Install conditions: temperature must be between 65-95°F with a maximum ambient RH of 65% for 48 hours before and during installation as well as for 72 hours afterward with the appropriate Open Time observed during installation. Surface must be structurally sound, dry, smooth, flat, and free of excess moisture/alkali and all substances (oil, debris, dust, paint, chemicals, oil based sealers, adhesive residue, etc.) that may inhibit the bond of the adhesive or the performance of the installation. Recommended Substrates: Porous wall surfaces such as gypsum drywall, plaster, brick, concrete block and wood. Limitations • ROBERTS 7200 is not recommended over nonporous, sealed or painted surfaces.

will this adhere to a painted block wall?

Asked by Boo July 28, 2020
1
Answer

No, ROBERTS 7200 is not recommended over nonporous or painted surfaces.

Would this product be good for glueing 1'carpet squares w/ vinyl back to cement walls? If not ca...

Asked by Doc April 27, 2020
2
Answers

I truly believe it would work fine.

Can i use this on vinyl fence that has a tear?

Asked by Jeff April 20, 2020
2
Answers

Jeff I have only used it for Cove Base against a sheetrock wall. I can tell you it drys quickly, not like superglue however. It will take minutes, cures in hours. The color was a creamy white, dries to a dark yellowish color. Once it is dry, difficult to clean up excess . Hopes this helps you.

How much time before this sets. Any wiggle room to reposition if needed?

Asked by Sweek April 5, 2020
2
Answers

Yes there is some wiggle room. It won’t truly set up for an hour or two depending on temp and humidity etc. simple repositioning within a few minutes or so shouldn’t be a problem

I am using MDF bender board for my base boards. I know that this typically used for vinyl base b...

Asked by slick1atwork March 22, 2020
1
Answer

7200 is specifically recommended for vinyl and rubber cove base application. This method could be possible with the 7200 however results & performance is unknown. Otherwise, you may want to consider a construction grade adhesive such as Loct Tite PL premium. Contact technical services for more information about Roberts products and installation. 706-277-5294 x6025

Can I use this to glue engineered flooring

Asked by JK March 19, 2020
1
Answer

No, 7200 is specific to wall base application. You may want to consider one of Roberts exceptional wood flooring adhesives - 1407 ( up to 5'' wide flooring) , 1509 urethane or 1535 urethane. For more information about Roberts products and installations Please contact technical services at 706-277-5294 x6025.

11 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube - page 2

Customer Reviews

  • 4.6
    out of 150 reviews
  • 89% recommend this product
5star-icon116
4star-icon20
3star-icon5
2star-icon4
1star-icon5
Filter by:
Showing 1-10 of 150 reviews
This 30 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube is well made and it is super econom...
This 30 fl. oz. Wall and Cove Base Adhesive in Cartridge Tube is well made and it is super economic. It delivers a great result at a very good price. Used it to glue times on the floor and it worked very well. I will definitively buy again if i need it.
by SmartShopper
26 people found this helpful
This stuff works like magic. By far my favorite adhesive for the purpose! And it looks great with...
This stuff works like magic. By far my favorite adhesive for the purpose! And it looks great with my newly installed flooring!
by Bri
1 person found this helpful
I used Roberts Adhesive when installing peel-n-stick linoleum tiles vertically on the wall as a b...
I used Roberts Adhesive when installing peel-n-stick linoleum tiles vertically on the wall as a backsplash. I was pleased with it's performance. The tiles were surprisingly heavy even though they are linoleum, so I wanted to be sure they were secure. When applying the adhesive, there is just enough of an open window to allow last minute adjustments if necessary. There is no odor whatsoever. I like the consistency, because it stayed on the wall as I applied it using a caulking gun. It didn't run or fall off the wall at all. It's just right.
by Vsss
6 people found this helpful
Didn't know in advance that I had to buy a large caulking gun. That was the only issue for us. My...
Didn't know in advance that I had to buy a large caulking gun. That was the only issue for us. My adult sons were able to install the vinyl baseboard in a timely manner. The product that we purchased along with the adhesive -- Roberts recommended spray nozzle worked well. Because we put the cove base on concrete walls in some areas, we had to use extra adhesive, but it got the job done. We are in the process of making our basement functional and the cove base put on with this adhesive is really making the place look professionally complete. Would highly recommend to anyone looking for non wood baseboards!
by Clinton
2 people found this helpful
Kitchen project complete!
The last step to our recent kitchen rehab was to put up the baseboard molding and an end panel for the island cabinet. This adhesive caulk was used on both. When I re-did the bathroom I used standard adhesive caulk for the baseboards before I found this stuff. The difference that I could see is that this is a lighter composition, comes out kind of like a foam and is not as inclined to drip out of the tube when you are not looking. It dried faster and filled gaps well. I still used nails to tack things in place, but only a few. I had hoped to not have to use nails on the cabinet end panel, but just like the longer baseboard, it needed something to secure it in place while the adhesive dried. Bottom line is that this is good for light weight adhesive projects.
by Stephen
8 people found this helpful
Rating provided by a verified purchaser...
Rating provided by a verified purchaser
by HomeDepotCustomer
Rating provided by a verified purchaser...
Rating provided by a verified purchaser
by HomeDepotCustomer
Worked great was able to apply the vinyl trim quickly....
Worked great was able to apply the vinyl trim quickly. Stayed firm. Great holding power.
by BARBARA
by HomeDepotCustomer
Rating provided by a verified purchaser...
Rating provided by a verified purchaser
by HomeDepotCustomer
Showing 1-10 of 150 reviews