$62.70
Pay $37.70 after $25 OFF your total qualifying purchase upon opening a new card. 
Apply for a Home Depot Consumer Card- Fastest way to connect PEX, copper, CPVC, PE-RT, or HDPE Pipe
- Requires no special tools to install on hot or cold-water lines
- Works on wet lines, rotatable after installation and removable
- View More Details
Product Details
No Tools Required
Installation requires no use of expensive tools, glues, solders, solvents, or crimping; all you need are pipe cutters.
Versatility
SharkBite Fittings are compatible with more than 5 pipe types: PEX, Copper, CPVC, PE-RT and HDPE.
Easy Fast Install
Installation is fast and simple within 3 seconds, allowing the job to get done in a snap. Allows fot the ability to work in tight spaces without having to make structural changes.
Approved for Underground
Approved for burial applications (wrapping required when burying underground)
Error-Proof
SharkBite Fittings are removable with disconnect clips or tongs, which will reduce the risk of installation errors
Wet or Dry Applications
Installation does not require a dry pipe and there is no need to wait for the pipe to drain, ProLock can be installed on a wet line.
Quality you can trust
SharkBite owns the entire manufacturing process, from raw materials to finished product
Versatile Fittings Collection
Full range of fittings and accessories 1/4 in. - 2 in.; Large diameter fittings (1-1/4" - 2") required Stiffener when connection to PEX Pipe
Certified
Listed by IAPMO and design certified and listed to ASSE 1061, CSA B125.3, NSF 372, NSF/ANSI 61, ASTM E84, CAN/ULC S102.2, ASTM, E119, CAN/ULC S101,UL289
Working Temperature and Pressure
Rated to 200°F and 200 PSI
Material
Made of durable DZR brass
Behind the Wall
Approved for behind-the-wall applications
Reliability
25 Year System Warranty
SharkBite large-diameter Push-to-Connect fittings are the fastest way to connect PEX, copper, CPVC, PE-RT, or HDPE pipe in any combination. They are available in 1-1/4 in., 1-1/2 in. & 2 in. CTS sizes. No soldering, clamps, unions, glue, or special tools are required. Simply insert the pipe and the teeth bite down and grip tight, while a specially formulated O-ring compresses to create a watertight seal. Changes can easily be made by rotating the fitting after installation. Removing the fitting is just as fast using a disconnect tool so fittings can be easily changed or reused. Designed with stainless steel gripping teeth for a secure connection, a chlorine-resistant O-ring for a long-lasting seal, and backed by a 25-year warranty.
- Push-to-connect fittings are ideal for installation in tight spaces
- Rated to 200 degrees Fahrenheit and 200 PSI
- Approved for underground and behind-the-wall applications with no access panels (wrapping required when burying underground)
- Can be installed on wet or dry lines and pressure tested immediately, no waiting on soldered joints to cool or solvents to dry
- When connecting to PEX pipe, a Stiffener (SBTL35, SBTL41, SBTL54) is required
- Fitting can be removed with a large diameter disconnect tool (UXLDC35, UXLDC41, UXLDC54)
- Low-lead DZR corrosion-resistant brass body
- Code approved, IAPMO listed, for details see Specifications
- 25-Year Warranty when used with PEX, copper, CPVC & PE-RT pipe
- 5-Year Warranty when used with SDR-9 HDPE pipe
- Shop all SharkBite Fittings
- Shop the SharkBite Polyethylene Pipe Collection
- Return Policy
- California residents
Specifications
Questions & Answers
55Questions
Q:What is the minimum gap or pipe cutout to utilize this. Or, how far does it extend from pipe end when fully slid onto the slip side?
by|Jan 3, 2023
1 Answer
Q:I?m trying to replace a leaking copper coupling which is just at 2?. Can I cut out a tad more that 2? inches?
by|Dec 16, 2022
0 Answer
Q:Can you confirm this will work for 1/2 cpvc plastic pipe?
by|Oct 29, 2022
2 Answers
Q:Dose the sharkbite work on a Copper air line?
by|Jul 26, 2022
2 Answers
Showing 1-4 of 55
Mar 16, 2022
Sharkbite pushin connector
This worked perfectly!!
by
Mar 6, 2021
You can make repair 1,2,3 first Time use five minute...
You can make repair 1,2,3 first Time use five minute 5: minutes great Product
by
Feb 24, 2021
When something looks too good to be true, there is usually a hidden cost or problem with it. Shar...
When something looks too good to be true, there is usually a hidden cost or problem with it. Sharkbite fittings are one product that breaks that mold. This is the second time I've purchased this particular product. First time was when a copper pipe in my basement sprung a leak due to a nail puncturing it when the house was built, and the nail finally rusting out of the hole. This was attached directly to an old dry floor joist, so I was hesitant to solder a new section in. I found this Sharkbite Slip Coupling, and what would have been an hour or more job, along with the possibility of burning down my house, turned out to be a five minute permanent fix. That was about 8 years ago, and there is has been no sign of leaking since.
I later had to replace the main shutoff valve for my house. Since the old one didn't completely stop the water, it would have been physically impossible to solder a new valve onto the pipe. I opted for the Sharkbite 3/4" ball valve instead, and had no trouble at all installing it even with the water trickling out the cut end of the pipe. I also had to shorten the pipe above the pressure regulator, so I turned again to the Slip Coupling fitting. And again, it made the job very easy. That was nine months ago, and so far it's holding pressure just fine. The only drawback is the cost of the fittings, but I'm willing to spend the extra for the safety factor (no torch work) and ease of installation.
by
Jul 21, 2020
Coupling was hard to slip onto copper pipe, leaked at first attempt to turn on water. Had to repo...
Coupling was hard to slip onto copper pipe, leaked at first attempt to turn on water. Had to reposition/adjust in order to stop leaking, finally was able to stop leak.
by
Response from RWC SupportAug 1, 2020
Hello, we are sorry to hear about the difficulty you experienced with the 1/2 in. SharkBite Slip Coupling. We recommend cleaning and deburring the copper pipe before installation for an easier installation and avoid leaks. Please reach out to our Customer Service Team at 1-877-700-4242 so we can troubleshoot and provide a solution.
Jun 26, 2020
Super easy to install
Used to replace cpvc connection to whole house water filter that had a slow drip. Not able to fully tighen the original installation since one end was fixed preventing the ability to rotate the fitting into the waterfolter body. Cut the cpvc pipe connection and installed a 1 inch nipple on the end of the Sharkbite coupling and tightened into the filter. Slipped the cpvc pipe into the coupling and turned the water back on. Worked like a charm and was very easy to install.
by
Jun 21, 2020
So worth it!
Used this on an ancient copper pipe under our cottage which had burst over the NY winter. I am not a plumber but I used the sharkbite deburring tool and slipped the sharkbite fitting on the first side. It took a couple of tries for me to move it back but it was obvious when it "clicked" into place. SUCCESS! And so worth it!
by
Apr 1, 2020
Extremely easy to install without any tools needed and also no leaks. Very satisfied. Highly reco...
Extremely easy to install without any tools needed and also no leaks. Very satisfied. Highly recommend .
by
Feb 29, 2020
Accidentally nicked a 3/4 inch copper pipe with a reciprocating saw. Of course I did this on a Sa...
Accidentally nicked a 3/4 inch copper pipe with a reciprocating saw. Of course I did this on a Saturday so getting a plumber in would have been very costly. I have never done any solder work on copper pipes. I'm pretty handy and I probably could have figured it out, but I was hoping for an alternate solution. Guy in the HD plumbing department suggested the SharkBite. I was a bit sceptical but decided to give it a try. I watched the video on the SharkBite website. Cut out a 2" section of the pipe where I nicked it and slid the SharkBite on one side then pushed over the side. Said a prayer and turned the main valve back on. Worked like a champ. When you first try to put the SharkBite on the pipe it seems that it does not want to go on and I was afraid that I might have done something wrong. After reviewing things and dermining that I was doing it per the instructions I just got a bit more forceful with my twisting and pushing and it slipped on the first pipe as it should. Same thing with moving it back over the second pipe. It will move with the proper amount of twisting and force. If you watch the SharkBite video they want you to use the SharkBite Depth Deburr Gauge (sold seperately) to clean the burrs of the pipe and measure how far you will slide the SharkBite onto the pipe. No need for that. Just use some emory cloth to clean the burrs and a ruler to mark the pipe.
by
Nov 23, 2019
This product does not work on existing pipes. After slipping one end on and the other half way on...
This product does not work on existing pipes. After slipping one end on and the other half way on, it would not go the rest of the way on, and it would not come off. Yes, thankyou, I did use the little tool, in fact I tried one on each end. After several calls to Sharkbite customer service I was told that some of the older copper pipe 'might' not work with this. Thanks for telling me that up front. Since I was working on the main water line and the house was without water, I had to call someone to help. The part had to be cut out and pex line was put in. The best way to express my experience with this product is what he said on the way out... trying to use SharkBite on existing pipes is an absolute disaster!
by
Response from RWC SupportNov 25, 2019
Hello, we are sorry for the difficulty you experienced with the SharkBite 3/4-inch Slip Coupling and we understand your frustration. SharkBite fittings do work with older copper pipe, however, we recommend to make sure that the pipe is clean and free of old solder and debris. The picture provided shows older solder on copper pipe. Having old solder on the pipe changes the diameter of the pipe and will not allow the fitting to be pushed to the full insertion depth. This may also cause the stainless steel teeth to get stuck on the pipe, preventing it from being able to slip. Again, we are sorry for the poor experience and hope you will try SharkBite again.
May 27, 2019
The perfect and easy fix
Well, no so easy to slide, but the sealing is perfect.
by
Frequently Bought Together
Price:
$6270
Compare Similar Brass Fittings
| | New |  | |
| Brand | SharkBite | SharkBite | The Plumber's Choice | |
| Name | 2 in. Push-to-Connect Brass Coupling Fitting | 2 in. Brass Push-to-Connect Slip Coupling Fitting | 1 in. Brass 90-Degree Push-to-Connect Elbow Fitting with SlipClip Release Tool (4-Pack) | 1 in. Tee Pipe Fittings Push to Connect PEX Copper, CPVC Brass (5-Pack) |
| Price | $4041 | $6270 | $6517 | $8113 |
| Ratings | (2865) | (685) | (65) | (5) |
| Fitting 1 size | 2" | 2" | 1" | 1" |
| Fitting or Connector Type | Coupling | Coupling | Elbow | Tee |
| Connectivity | Push Fit | Push Fit | Push Fit | Push Fit |
| Application | Potable Water | Potable Water | Potable Water,Rough-In valve,Water Supply | Potable Water |
| Features | Lead Free,Removable | Lead Free,Removable | Lead Free,Removable | Corrosion Resistant,Lead Free,Removable |
| Pack Size | 1 | 1 | 4 | 5 |
| Material | Brass | Brass | Brass | Brass |
| View Product | View Product | View Product | View Product |
Related Searches
Related Products
Explore More on homedepot.com
Appliances
Flooring
Hardware
Home Décor
