![]() | ![]() | ![]() | ![]() | |
Brand | Wayne | Wayne | Wayne | Wayne |
Name | 1/2 HP Non-Clogging Vortex, Reinforced Thermoplastic Submersible Utility Pump | 0.16 HP WaterBUG Glow Auto Off Submersible Utility Pump with Multi-Flo Technology | EEAUP250 1/4 HP Submersible Utility Pump | 1/2 HP Cast Iron, Portable Transfer Utility Pump |
Price | $6837 | $12900 | $15873 | $16464 |
Ratings | (395) | (123) | (16) | (232) |
Discharge Flow @ 0 ft. (gallons/hour) | 2600 | 1350 | 3100 | 1450 |
Housing Material | Thermoplastic | Thermoplastic | Thermoplastic | Cast-Iron |
Voltage | 115v | 120v | 120v | 115v |
View Product | View Product | View Product | View Product |
![]() | ![]() | ![]() | ![]() | |
Brand | Wayne | Wayne | Wayne | Wayne |
Name | 1/2 HP Non-Clogging Vortex, Reinforced Thermoplastic Submersible Utility Pump | 0.16 HP WaterBUG Glow Auto Off Submersible Utility Pump with Multi-Flo Technology | EEAUP250 1/4 HP Submersible Utility Pump | 1/2 HP Cast Iron, Portable Transfer Utility Pump |
Price | $6837 | $12900 | $15873 | $16464 |
Ratings | (395) | (123) | (16) | (232) |
Discharge Flow @ 0 ft. (gallons/hour) | ||||
Housing Material | ||||
Voltage | ||||
View Product | View Product | View Product | View Product |
It protects the pump motor from burning out if the water level is too low to draw. If it shuts off, allow one hour cool-down time and then plug it back in
I use a 75ft hose with mine with no problems
My pool cover it under tension the pump cannot suck the cover up and close the pump openings, that is the difference.
Yes
I used a 14 or 16 gauge 50 foot cord attached to a ground fault outlet but a 12 gauge would be better. I also bought a ground fault outlet that can be plugged into a regular outlet to create one if needed. seems like a good idea since it is submerged for pumping out water
The WaterBUG Glow has an open impeller which is less prone to clogging and passes some debris through. The recommended operation is to place to the pump on a hard surface in the water. The filter features of this pump work best if the debris is filtered from the outside in. Sitting the pump directly on a loose/dirty surface will not allow the filter features to work to their full extent.
It should start back up when its put in water again
This is the way I look at head pressure verses vertical lift, head pressure is the maximum amount of water pressure discharged at 25 feet of hose after that the longer the hose the less pressure and volume your pump will discharge water, Vertical lift is the height the pump will pump maximum amount of water at that height each foot you pump higher you will lose volume, if your pumping 10 foot you will pump Max. if you pump 12 foot you will pump less and so on .
We have this pump, it depends on how much you are going to irrigate, we have an orchard and vineyard we pump water from tanks to the needed areas it works well for us, we wanted the pump because it pumps water from one of our shop floors, the water never really floods sometimes it gets maybe a quarter of an inch deep in a place or two, this little pump will pump it out in a couple of minutes.
I would store it at a more moderate temperature if I had a choice, especially if it had been used to pump water. In the winter here in the mountains, I store our vehicle batteries and cordless tool batteries in the basement, where although it gets cold, it does not freeze like it does up in the barn. Stuff just seems to last longer that way.