#1 Home Improvement Retailer

Questions and Answers for HyLoft 2-Shelf 45 in. W Wire Garage Wall Storage System in White

Internet #100656717

Model #00967

Store SKU #1002263268

  • 200 lbs. holding capacity ensures optimum storage of contents
  • Steel frame with scratch-resistant white finish for long-term use
  • Low-profile brackets save space and offer simplified installation

Questions & Answers

22Questions
caret
Q:how long are the shelfs #00967,0077
by|Jan 15, 2018
5 Answers
Answer This Question

A:  As the product description says, 36”

by|May 5, 2023

    A:  The shelves are 36" wide by 18" deep. The nice part is the hold 150lbs of weight. There are also hooks that you can buy to hang stuff below the self. That's great for hanging extension cords and lawn tools.

    by|May 5, 2023

      A:  Well, I thought the 36 " included in the product description was a dead give away. They are 18 " wide. They also have 48" long x 16" wide.

      by|May 5, 2023

        A:  They are 36 inches wide. You can determine the amount of space you want want between them when you mount 2 or more. I spaced mine about 18 inches apart and they are excellent for extra storage in my kitchen. I also put them side by side in my basement for extra off the floor storage.

        by|May 5, 2023

          A:  The Hyloft 00777 shelves are 36" Wide and 18" Deep. The Hyloft 00967 shelves are 45" Wide and 15" Deep.

          by|May 5, 2023
            caret
            Q:I want to cancel this order and order a different item. How do I do that?
            by|Nov 1, 2017
            0 Answer
            Answer This Question
            caret
            Q:How wide are the brackets that hold it and can the wire shelving be cut. The space I want to put the shelving in is only 70" across
            by|Sep 13, 2017
            5 Answers
            Answer This Question

            A:  I would buy one unit, inspect it, and if it doesn't work, box it up and return it to Home Depot. I believe it will work cutting it down the 2 inches you need cut off.

            by|Jan 17, 2019

              A:  The part of the bracket that attaches to the wall is 1 and 1/2 " wide and the part of the bracket that supports the shelf is 1/4 " wide. I will defer to the manufacturer on whether the shelves can be cut but absent that, after looking at them, I think it might work but I suspect that you will need a sturdy hacksaw and quite a bit of energy to accomplish it. Personally, I don't think I would. If I had a 70" wide space and wanted to use these 36" shelves which lengthwise makes the most sense for a 70" wide space, what I would do is mount one shelf and mount the 2nd shelf about 1/4 to 1/2 inch higher, or lower, so that the 2 shelves would overlap approximately 2 inches and one shelf would overlap and lay on the other for about 2 inches. I did just that but my overlap was about 1" but I ended up undoing it because I decided to change the arrangement of the different lengths of the shelves which meant that the offset set of holes wasn't used. Let me caution you that if you mark and drill a set of holes in a stud and then decide you want them 1/4 to 1/2 inch higher or lower, I think the 2 sets of holes will be too close to each other vertically to allow mounting the bracket successfully. Knowing what I know now, I know I could do what I just described successfully assuming you have studs to mount to which if it is in a house built to modern standards, you almost certainly do.

              by|Jun 19, 2019

                A:  Since I never had a reason to cut the length of the rack and can't guarantee it will work. Based upon the design of the rack, I feel it can be cut length wise. I would assume you can and then order one unit and take it out of the carton and inspect it. If you feel you can't cut it down, put it back in the carton and return it for credit. Quality wise this is an excellent product. Modification wise I think you are going to have to look at the product and decide for yourself.

                by|Jan 17, 2019

                  A:  For my shelves, the brackets are about 28 "- 32" apart. The most important part is they should be mounted to studs. I don't see why you cannot cut it but there are a lot of wires to cut through. The shelves cannot overlap like the Rubbermaid closet shelves. I suggest you check them out too.

                  by|Nov 22, 2017

                    A:  Since the pole telescopes you can set the distance between the brackets from 22" to 35". However, if you cut the shelving you will void the manufacturers limited lifetime warranty.

                    by|May 4, 2023
                      caret
                      Q:Can you attach to Sheetrock wall and how much weight can hold?
                      by|Mar 29, 2017
                      5 Answers
                      Answer This Question

                      A:  I would try to find the wall studs behind the drywall for best results. I purchased a stud finder that did the job fir me.

                      by|May 5, 2023

                        A:  Find studs and anchor the bolts in the studs. Each shelf is rated to hold up to 150 lbs (assuming they are bolted into the studs).

                        by|Nov 6, 2018

                          A:  Yes, the brackets can be installed through sheetrock into studs and will each hold up to 150 pounds. If brackets are installed using drywall anchors instead of screwed into studs, the holding capacity will be much less.

                          by|May 4, 2023

                          A:  Yes you can attach to sheet rock wall. Just make sure you find the stud and attach it there. Do not randomly screw into the wall with nothing to hold it.

                          by|May 5, 2023

                            A:  You can mount to a wall that has sheetfock on it, however you need to mount through the sheetrock and into the wall studs. When installing into the studs, and using the supplied fasteners, the unit will hold up to 150lbs per shelf.

                            by|May 4, 2023
                              1 found this answer helpful
                              caret
                              Q:I need to screw brackets to a block wall. What type and length of a screw should be used.
                              by|Feb 22, 2017
                              2 Answers
                              Answer This Question

                              A:  We used and 1/1/4 inch tapcon screws

                              by|May 4, 2023

                                A:  You will need to use a concrete sleeve anchor. Do not use concrete or masonry screws. We recommend a 3/8" anchor that uses a 5/16" diameter bolt. We recommend using a 1-3/4" or similar length sleeve anchor. You need to be use more than a 1-1/2" long sleeve anchor.

                                by|May 4, 2023
                                  1 found this answer helpful
                                  caret
                                  Q:Is it 150 pounds per shelf?
                                  by|Dec 20, 2016
                                  5 Answers
                                  Answer This Question

                                  A:  Each shelf supports up to 150 pounds.

                                  by|Jan 17, 2019
                                  1 found this answer helpful

                                  A:  The weight limit is for each shelf.

                                  by|Jan 17, 2019
                                    1 found this answer helpful

                                    A:  Yes. I installed shelves side by side so I was careful not to overload any point on the shelves in excess of 150 lbs.

                                    by|Jan 17, 2019
                                      1 found this answer helpful

                                      A:  Our facility is only using it for child car seat storage. Based upon our usage I have no way of knowing if each shelf will support 150 lbs. I recommend that you find the contact information from Home Depot of the manufacture and direct your question directly to them. That way if they say it will support 150 lbs. and it doesn't, if you have a failure, it will become the manufacturers problem if it fails. Hope this helps.

                                      by|Jan 17, 2019

                                        A:  The information on some of the descriptions of this product on some web sites state this system is rated to 150 lbs. To cover you liability, I would contact the manufacture and have them verify in writing that these shelves will support up to 150 lbs.

                                        by|Jan 17, 2019
                                          1 found this answer helpful
                                          caret
                                          Q:The installation sheet mentions to drill into a stud. If that's not an option, can it still be mounted into drywall if the plan is not to load the shelf to the max of the spec?
                                          by|Oct 17, 2016
                                          5 Answers
                                          Answer This Question

                                          A:  They work best if drilled into a stud and will hold more weight.

                                          by|May 4, 2023

                                          A:  This product was designed and includes hardware for mounting in to wall studs. No weight load testing has been done for any other applications so there is no way to ensure what weight load this product would hold when not installed in to wall studs.

                                          by|May 4, 2023
                                            2 found this answer helpful

                                            A:  Given the depth of the shelf, i.e., long moment arm for weights place on outer edge, use wall board anchors designed for very high loads. Three anchors per mount so that should work okay vs needing stud.

                                            by|May 4, 2023
                                              1 found this answer helpful

                                              A:  I would recommend a stud.

                                              by|May 4, 2023

                                                A:  The screws included with these shelves are large enough that they really need go into a stud. Plus, even though the shelf itself doesn't weigh much, by the time you put a few pounds on it, it'd likely pull out of the wall.

                                                by|May 5, 2023
                                                caret
                                                Q:I SEE 2 1/4 IN HEIGHT. I AM ATTACHING THESE TO A METAL BUILDING CROSS BEAM. THE LIP IS NARROW AND I NEED TO SEE IF THERE IS SPACE TO CONNECT BRACKET TO.
                                                by|Sep 28, 2016
                                                4 Answers
                                                Answer This Question

                                                A:  Aprox 4.5"

                                                by|May 5, 2023

                                                  A:  The distance from the center of the top hole to the center of the bottom hole is 4". the over-all height of the bracket is 5-1/2".

                                                  by|May 4, 2023
                                                    4 found this answer helpful

                                                    A:  4 inches. 3 bolts per anchor. Lag bolts provided. 2 bolts go into wall below shelf, one bolt above shelf. Shelves have rubber keepers you insert between shelf edge and wall braces to prevent shelf from moving once installed.

                                                    by|May 4, 2023
                                                      2 found this answer helpful

                                                      A:  It's about 5". I've included a photo so you can (hopefully) see.

                                                      by|May 5, 2023
                                                      caret
                                                      Q:Are each of the shelves 45" in length or is 45" a combined length
                                                      by|Sep 21, 2016
                                                      5 Answers
                                                      Answer This Question

                                                      A:  Each of the shelves are 45".

                                                      by|May 4, 2023
                                                        6 found this answer helpful

                                                        A:  Each shelf is 45" in length

                                                        by|May 5, 2023

                                                        A:  each shelf is 45"

                                                        by|May 4, 2023

                                                          A:  Each is 45 inches long.

                                                          by|May 4, 2023

                                                            A:  Each shelf is 45 inches long.

                                                            by|May 4, 2023
                                                            caret
                                                            Q:Please identify/recommend the proper slatwall choice(s). And, will the Gladiator 96" 2 pack slatwall be compatible, Model GAWP082PBY?
                                                            by|Sep 11, 2016
                                                            3 Answers
                                                            Answer This Question

                                                            A:  I have Gladiator in part of my garage and the channels are too wide for this slat wall. These shelves will slip out with too much weight. I purchased a couple pieces of the Rubbermaid Fast Track panels and they work perfectly.

                                                            by|May 5, 2023

                                                              A:  It works with GarageTek wallboard.

                                                              by|May 4, 2023

                                                                A:  Our slat wall shelf kit is not designed to work with any particular brand of slat wall, thus we have not tested this to work with Gladiator’s products. We can tell you that since we hook into only one slat the center-to-center from one slat to the next should not be an issue. Our hook on our bracket has a depth of approximately .6” and height of .72”. If the slat wall you purchase has an opening that will accommodate this size hook our system will work with it. Our system does work with most common slat wall sold at major retailers.

                                                                by|May 4, 2023

                                                                  Compare Similar Items