A: thin but sturdy enough stick on carpet and be walked on. Warning: but do NOT leave it on the carpet for more than a few hours otherwise it will leave a residue which cannot be removed.
A: Thank you for your inquiry. Unless otherwise stated, all of our Carpet Shield products are 2.8 mil's (0.0028 inches) thick. This provides both protection of your carpet as well as the necessary flexability to work on its surface. Please reach out to surfaceshields.com/contact-us with any further questions.
A: When our products are used within specification end users tend to have a positive experience. If you have any questions or concerns about our products please contact customer service for further assistance.
A: No because it doesn't stick at all
A: Yes
A: Yes. We have a roller applicator which helps to apply it, but it can be applied by one person. Peel some back, apply it and kneel on it to get started.Once you get two to three feet stuck down, you can stand behind it and pull it the length you need it and lay it down. Hope this helps.
A: Yes.
A: Thank you for your inquiry. Yes, "reverse wound" means the tacky part of the Carpet Shield self-adhesive film is on the outside of the roll making it easier to apply to the carpet. If you have any further questions please feel free to reach out to us at surfaceshields.com.
A: adhesive is on the outside of the roll
A: It doesn’t leave a visible residue or any stickiness. I’ve used it several times without an issue.
A: Yes, carpet cleaning with special cleaning products and methods will remove the residue. If you had issues of residue from this product, it's possible it was left on the carpet to long or possibly a defective batch. No number on the bow, but try their website at www.surfaceshields.com
A: Thank you for your inquiry. We do not suggest cleaning the carpet. We recommend that you submit a case on our website so that we may service you best. Simply copy and paste the link and fill out the information requested: https://www.surfaceshields.com/case-form. A customer service representative will contact you further once your case has been submitted and received into our system.
A: I am sure it will work on wood floors yet since the adhesive is so strong I would be hesitant to use it on wood floors. If your floor has any protection sealant on it, the sealant might be removed when pulling up the film.
A: Thank you for contacting us. Carpet shield is a temporary carpet protection product intended for synthetic carpeting only. We do not recommend using this product on a hardwood surface. We recommend considering using the multi surface protection. It is a durable, self-adhering protective film for hard surfaces, such as tile, marble, granite, vinyl, VCT, laminates and factory finished hardwood. Here is a link for your convenience: https://www.surfaceshields.com/multi-surface. Should you have any outstanding questions, please select the “contact us” tab on our website to submit a general inquiry or call to speak with a customer service representative. We hope you find this information useful.
A: im not sure, i used it on carpet
A: Would not recommend. I used it on LVT and it left a sticky residue that is difficult to remove.
A: Not sure but great for carpet
A: No, it is not recommended to be used on a wool rug.
A: Hi Laura. Thank you looking into our product when looking to protect your rug. Unfortunately, Carpet Shield is designed to work with synthetic carpet fibers only. If you need help protecting your wool rug during your project please look into Ram Board, which can protect a wide variety of surfaces or feel free to reach out to us at surfaceshields.com and we can suggest a product for you. Thank you and good luck!
A: Scissors or a box knife
A: Thank you for your inquiry. Any bladed edge (scissors, a utility knife, the Ram Board Multi-Cutter, etc) can be used to cut Carpet Shield, but no matter what item you use to cut Carpet Shield care must be used not to damage the surface you are trying to protect. Feel Free to reach out to us at surfaceshields.com with any further questions. Good luck with your project!
A: I used a blade.
A: Utility knife.
A: I used a razor blade. Carefully.
A: Thank you for your inquiry. There are several accessory options for dispensing this product. Please reach out to us at surfaceshields.com or follow this link to our website to view them: https://www.surfaceshields.com/catalogsearch/result/?q=applicator. We hope this information is found useful!
A: Hi Ray. The Carpet Shield film you are inquiring about is 2.5 mils thick. If you have any further questions about Carpet Film please feel free to reach out to us at surfaceshields.com or follow this link to the spec page for the product: https://www.surfaceshields.com/pdfs/spec-sheets/2015%20Spec%20Sheet_Carpet%20Shield.pdf . Thank you for considering the use of our product.
A: This product is 1 mil in thickness.
A: I was concerned about that too but it was safe to walk on. Might be a little concerned if shoes were wet.
A: Not at all
A: No
A: Not at all.
A: Thank you for contacting us regarding your inquiry. Carpet Shield is a temporary 30-day carpet protection product only to be used as directed. If the product is applied to suitable carpeting, the product will adhere to the surface and it will be effortless to walk on. If there are damp or wet elements being tracked into the home or onto the surface of Carpet Shield, we would recommend drying your shoes off and walking with caution to avoid slipping. If you have any additional questions regarding our product, please contact us. Our information is available at https://www.surfaceshields.com/.
current item | |||
Flooring Material Features | |||
---|---|---|---|
No Additional Features | Moisture resistant, No sealing required, Stain resistant | No Additional Features | No Additional Features |
Material | |||
Polyethylene | Paper | Vinyl | Vinyl |
How can we help?