Questions and Answers for ZEP 1 Gal. Heavy-Duty Floor Stripper (4-Pack)

A:  Yes. Zep Heavy Duty Floor Stripper Concentrate is suitable for use on most interior floors including vinyl composition. Always test in an inconspicuous are prior to use. Follow dilution for light to medium floor stripping: Mix 16 ounces of Zep Heavy Duty Floor Stripper Concentrate with one gallon of hot water. Use a cotton mop to apply solution and damp mop floor. Stubborn areas may require reapplication and/or agitating with a brush. Rinse floor well with clean water. I hope this helps! - Zep Inc.

A:  No, unfortunately. Avoid use on sensitive floor surfaces including, marble, granite, slate, and other natural stone floors. I hope this helps! - Zep Inc.

A:  Yes. Follow the dilution for heavy duty stripping. Dilute 64 ounces of Zep Heavy Duty Floor Stripper Concentrate with one gallon hot water (130° - 150°F or 54° -66°C). Generously spread solution over area to be stripped with a cotton string mop and allow to soak 5-8 minutes. DO NOT allow stripper to dry before rinsing. If desired, agitate with a brush or stripping pad. For heavier jobs, use a low-speed stripping machine. Pick up solution completely with a clean mop or wet vacuum. Rinse twice and allow to dry before applying a sealer suitable for exterior concrete. - Zep Inc.

A:  i would use only on solid surface like porcelain or vinyl tile

A:  Yes...it will take anything that's ever been applied to the tile and leave the tile clean...some scrubbing with a long handle brush will take everything off after the zep sits and works for ten minutes.

A:  Yes...I used it outside on ceramic tiles that the prior home owner applied heavy coats of was on that had turned yellow. Also the entire inside of the house where the same wax was applied on all tile. It was a mess. I poured it on full strength then used a mop to push it around. Do a 5 foot square of tile at a time so it doesn't dry. You'll have to scrub a bit. But it takes everything off.

A:  I used this as a floor stripper and don't have a clue as to how to advise you. I would go to the ZEP website and seek an answer there.

A:  No this will not dissolve that kind of wax. what you should do is cover wax with junk towel and heat with low iron to melt and absorb wax. go slow and move towel so you dont redeposit wax

A:  Absolutely. Test product in an inconspicuous area before use and allow area too dry to determine compatibility. For Light to Medium-Duty Stripping: Dilute 16 ounces of product with 1 gallon hot water (130° - 150°F or 54° - 66°C) - a 1:8 dilution. For Heavy-Duty Stripping: Dilute 64 ounces with 1 gallon hot water (130° - 150°F or 54° - 66°C) - a 1:2 dilution. Apply the solution liberally with a cotton mop, and allow solution to soak 5-8 minutes . Use a brush or scrubbing pad if necessary to agitate stubborn areas, then remove solution with a wet vac or mop. Rinse floor twice and allow to dry. I hope this helps! If you require further assistance, feel free to call 1-888-805-4357. We appreciate your business and look forward to servicing you! - Zep Inc.

A:  Yes. Zep Heavy Duty Floor Stripper Concentrate removes adhesive and glue. Mix 16 ounces of Zep Heavy Duty Floor Stripper Concentrate with one gallon of hot water. Generously spread solution over area with a cotton and allow to soak for 5-8 minutes. If necessary, agitate with a brush or stripping pad. For heavier jobs, use a low-speed stripping machine. Pick up solution completely with a clean mop or wet vacuum. Rinse twice and allow floor to dry before sealing and polishing. I hope this helps! Should you have any questions, feel free to call 1-888-805-4357. We appreciate your business and look forward to servicing you! - Zep Inc.

A:  Sorry, I used it on ceramic tile not laminate so I can’t say if it’s safe. The bottle says it’s okay to remove wax buildup on linoleum though. You might test it on a small area of your laminate that would not be noticeable if it were damaged by the cleaner. The stripper must be rinsed off after applying and removing wax. It has a strong chemical odor and is very harsh. So I would use a more gentle cleaner or contact the manufacturer directly and ask specifically about whether you can use it on laminate. Good luck!

A:  Hi, Alex Thank you for your inquiry. Zep Heavy Duty Floor Stripper Concentrate is not suitable for laminate and/or laminate wood floors. Should you have any further questions, feel free to call 1-888-805-4357. We appreciate your business and look forward to servicing you! – Zep Inc.

A:  This stripper is best used to remove polishes, temporary shine products and other pour on from retail stores applications that clean and leave behind a shiny surface.  As these products age, discolor, build-up etc this product will remove them and leave the original finish in tact.   If the clay does not have an original finish this product may discolor the base original clay.  It it is a sealed tile use the same caution but it should work fine on sealed products. No matter the flooring always cut this product with water and apply it in a non conspicuous area like somewhere in a closet, under where a rug or furniture would be or even an appliance.  Go slow until you know the impact on your floor. 

A:  Absolutely. Mix 16 ounces of Zep Heavy Duty Floor Stripper Concentrate with one gallon of hot water. Use a cotton mop to apply solution to floor and allow it to soak for 5-8 minutes. For stubborn areas, agitate with a brush or low- speed stripping machine. Pick up solution with a mop or wet vac. Rinse floor well with clean water. I hope this helps. Should you have any questions or require further assistance, feel free to call 1-888-805-4357. We appreciate your business and look forward to servicing you!- Zep Inc.