Customer Reviews for Avanti Pro 8 in. x 24-Tooth Stacked Dado Circular Saw Blade Set

Does the job for inexpensive Dado, but will tear the edges on plywood dado

So far everything is as advertised

The blades are in a nice case and they are easy to setup and clearly labeled. I have only used a few times but they are exactly as described and work great. The 1/8th size is correct when using the spacers - tested up to 1/2 inch and plenty for my projects. Have not needed the 1/6th but I am sure it is also sized correctly.

A low cost experiment for a few tenon joints with random door jambs. If two of these saw blades have arrows that say line up. You line them up to not move while running. I snugged a 3/8" combination on my Delta tablesaw (rpms match). $50 piece of oak 1x, I could cut all day. It ran smooth and fun. Not that my next Dado won't be a different brand. Don't be concerned if you have the 30.5" Delta tablesaw. They're rated for each other and would result tight fits with oak.

Works as advertised, nice clean cuts.

Did a pretty decent job once I got it set up right.

Blade could be a finer tooth but is adequate for joinery cuts on projects such as fencing gates and other light construction.

It makes a dado but will require tlc afterwards. Probably wouldn't buy again..

Cheap Wood box coming apart. Paper thin veneer peeling off right out of the package. Outer blades are not chisel point leave groove on each side of dado. If you are looking for clean flat dados this is not for you.

I picked this set up due to the price and being fairly new to using a dado. However, this set did nothing to help me with my work. I could not get an even cut with these and it wouldn't produce a square cut. I tried every combination possible and the cuts always came out the same. I wish I had spent the extra money for a better set. I wouldn't even recommend a beginner for this set. All it did was make me mad. Do yourself a favor and spend the extra money.

Impossible to get a flat cut. Doesn't matter how you shim or rotate and offset the chippers. The end blades are diagonal and will leave bat ears. The chippers are not the exact same diameter. This leaves more peaks and valleys than anything I've ever seen.

I used this to cut notches in fence posts. Worked great.

I bought this because I was cheap to buy a quality dado set. I used it successfully twice, a total of about 10 cuts. When I went to use it a third time, I noticed that it was rubbing against the motor support bracket. It turns out that the bladed warped to the point of being dangerous and unusable. This set went straight into the trash, and I wasted $60 when I should have spent 40 more and gotten a freud set.

I bought this blade set back in January and finally got around to using it. To start, the arbor holes in most of the spacers, blades and chippers did not fit my 5/8"arbor saw very well. Once I did get around to actually cutting with the setup I was extremely disappointed at the refinish it left. I double checked the direction of the blades - both were facing the correct direction - and made another pass. No change. The blades and chippers were all cutting at a different level. Poor QC.

This dado has worked great for me and i haven't had the issues with not cutting a good channel but i made sure the blades were seated correctly. For the price it was a great addition to the tablesaw.

Did not fit my saw though the information provided said it would. Not worth the money I spent on it and not worth the money it would cost to send it back.

Rating provided by a verified purchaser

The blade is great. The case it comes in breaks very easily.

STOP SENDING THESE, I PURCHASED A SET AWHILE BACK AND YOU KEEP SENDING MORE ...PLZ STOP....

Rating provided by a verified purchaser

Rating provided by a verified purchaser

Worked better than I had anticipated. I would recommend this dado set to others, I would also repurchase this set again as a secondary for my other table.

It worked out perfect. The price was good too.

No problems with setup. Worked very well

Will not fit my table saw.

Cuts very clean dados.

Appear to be a decent value for the money. I have not used them yet but they seem to be of good quality and none of the carbide teeth were chipped. I am novice woodworker and the dado set will be used, but not extensively. If woodworking was my profession I would have ordered a higher end set. I already have had a 10" Avanti 60 tooth blade in my miter saw which has served me well for over 10 years now - part of the reason why I purchased the dado set. I will update this if needed after I use the dado set.