#1 Home Improvement Retailer

Customer Reviews for Everbilt 3/4 HP Shallow Well Jet Pump

Internet #204478353

Model #J200A3

Store SKU #1000026692

  • Pumps up to 552 GPH of clear water at 40 PSI
  • Lead free self-priming pump design for water depths to 25 ft.
  • Thermoplastic housing reisists corrosion for long-term durability

Customer Reviews

  • 4
    out of 578 reviews
  • 78% recommend this product
Filter by:
Showing 1-30 of 578 reviews
We received the pump in good condition. The packaging is minimal but effective with just 2 pieces...
We received the pump in good condition. The packaging is minimal but effective with just 2 pieces of foam holding it suspended in the box. Our install is scheduled for later this month, so we could not performance test it yet. A few notes. This is a dual voltage single phase pump. Switching voltage is done with a switch inside the junction box. Easy wire hookup instructions are on the lid. The water connections are threaded 1.25 inch npt suction, 1 inch npt discharge. Use of pvc pipe connections are recommended. You will need a bladder tank charged to 28 psi already installed for this system to work properly. The start is set to 30 psi, and stop set to 50 psi. The pressure switch is easily adjusted with a small wrench. The clear supply tube to the pressure switch makes it nice so that you can see debris clogging and remove them if the pump is having issues. The gauge is great for setting the system up, but I personally prefer a liquid filled gauge for logativity. Its easy to replace with your own .25 inch npt gauge. This pump is designed specifically for shallow wells 25 feet or less and has an average flow rate of 7-4.5 g.p.m. if you are doing a fresh install of this pump, pay attention to the fittings and pipe needed. I would recommend a pro install and set up with this product unless you are familiar. I have used this brand prior and like to overall quality and reliability of this brand. The warranty is only 1 year, but for the price it is a steal.
by
  • Recommended
This is a great value! This 3/4 HP, 115 volt Shallow Well Jet Pump by Everbilt is a best seller a...
This is a great value! This 3/4 HP, 115 volt Shallow Well Jet Pump by Everbilt is a best seller and the design and price are just two of the reasons. Performance and ease of installation are two more excellent reasons. Rust-free engineering and 3/4 HP motor will last many years, whether installed in an interior or exterior location. Add features like self-priming and a fan-cooled motor and you have a great pump at a very good price. While it says it is designed for 25 feet or less, the vertical lift length is specified for 148 feet! And the volume is very good at 9 gallons per minute. The pump is also backed with a one year warranty. This is a very nice pump at a very nice price.
by
  • Recommended
Everbilt 3/4 HP Shallow Well Jet Pump We needed a new well pump for our water system. It will fi...
Everbilt 3/4 HP Shallow Well Jet Pump We needed a new well pump for our water system. It will fill a holding tank. The water table ranges from 10 to feet depending on the time of the year. I must have got about a dozen Everbilt pumps over the years, and it is my go to brand for above ground pumps. Because our water quality can be very hard, the thermoplastic is a better fit and does not rust anywhere near as fast as cast iron. Very easy to install with great instructions and company online videos if you are a notivis.
by
  • Recommended
Very nicely made well pump. The motor has some weight to it and has a nice metal enclosure. The p...
Very nicely made well pump. The motor has some weight to it and has a nice metal enclosure. The pump housing (while lightweight) is very sturdy made of an ABS plastic type material. The built in gauge seems to be high quality and works great as did all of the plumbing connections. The pump has plenty of power and the pressure matches that of most city water I have seen. If your installing at 110v make sure you confirm the switch is switched to 110v and not 230v!
by
  • Recommended
The Shallow Well jet pump. So this is a replacement for unit that failed and this Everbilt fits ...
The Shallow Well jet pump. So this is a replacement for unit that failed and this Everbilt fits the expansion tank already in place. It is pretty simplistic for swapping out and performance for our use is not under powered.. So here’s what you need to know. 110 or 220 connected the same a changed by a switch under the electrical housing cover. It comes with 30-50 PSI pressure switch so even the max pressure of this pump is 66PSI the pressure switch will not allow you to get there. Maximum depth is 25 feet .You will need additional items to install this is a pump only. Working well in our application . My biggest gripe is lots of plastic, pump housing electrical covers and pressure ine. This unit is supplying water to and emergency water tank. Fire just swept the area and melted parts making this unusable. My bad new unit is inclosed in a cinder block enclosure now.
by
  • Recommended
This is a review for the Everbilt 1/2 HP shallow-well jet pump. The pump comes with a 0-100psi pr...
This is a review for the Everbilt 1/2 HP shallow-well jet pump. The pump comes with a 0-100psi pressure gauge and the built in pressure switch is set for a 30 psi "ON" setting and a 60 psi "OFF" setting. The motor comes prewired for 230-Volt installation but states it can be changed to 115V. The well I am going to use it for is right at 22 feet deep so this unit should fit the bill for my needs. The pump comes ready to install but it DOES NOT come with a foot valve or check valve so make sure to purchase one before starting your project. The install looks fairly easy so off I go!!
by
  • Recommended
2 found this review helpful
The Everbilt 3/4 HP Shallow Well Jet Pump is designed for shallow well home drinking water supply...
The Everbilt 3/4 HP Shallow Well Jet Pump is designed for shallow well home drinking water supply connections. The pump can be installed using 115 or 230 volt wiring (power cord is not included) and then electrical setup is as easy as flipping a switch. The pump is setup for a low pressure turn on at 30 psi and shut off at 50 psi, and is rated for a max pressure of 65 psi. At the maximum inlet depth (25 ft), the unit will flow 6 gallons a minute at 40psi. Requires a suction pipe size of 1-1/4" FNPT with a foot valve or check valve installed. This pump comes ready to install and is designed for wells with pumping levels of 25 ft depth. or less, pump inlet should be no deeper than 25ft below ground surface, with 10 ft of water column above the inlet and at least 5 feet to the bottom of the well below the inlet. The unit is required to be primed for the initial start up, but is then self-priming after initial start up. The composite body will not rust or corrode with acidic and should be resistant to lime scale from hard water. A drain plug is included for easy winterization and draining. This pump comes with a 1 year warranty from the date of purchase.
by
  • Recommended
1 found this review helpful
EVERBILT 1/2 HP SHALLOW WELL JET PUMP This jet pump has a plastic pump housing and impeller. I am...
EVERBILT 1/2 HP SHALLOW WELL JET PUMP This jet pump has a plastic pump housing and impeller. I am not concerned about rust with this pump. Rusty water has been a problem with the cast-iron pumps I have been using. My main concern over this pump is in the warning on the rear of the pump. It states that the pump may become stuck if not used for a "period of time " and what to do about it. Features that I like is the easy method to change the power from 115/230. Instructions are very simple and clear, listed on the pump and Instructions sheet.
by
  • Recommended
Great pump for home well potable water needs and other operations where you need high water flow ...
Great pump for home well potable water needs and other operations where you need high water flow capacity. It's nice to keep a well pump as a spare because they always fail at the worst time. These Everbilt pumps are economical and great to keep at the cabin in case the primary pump quits on you. This is prewired for 115 and 230 volt input. Specs are as follows: Size 15.1 inches long 8.5 inches tall 7.9 inches wide 115volt draws 20 amps. 230 volts draws 10 amps. Simply flip the internal switch to 115V if needed, the pump is set to 230V from the factory. 1 inch FNPT discharge size Intake 1 to 1/14 inch 25 foot deep water level max Water flow rates at feet of head, 40psi. Max pressure 65psi: 0ft 9.2GPM 25ft 6 GPM Self priming after casing is filled with water initially. Do not run dry. Pressure gauge built in. Thermoplastic housing. 1 year warranty. These types of pumps work well for irrigation pumps and waterfall pumps as well as its intended purpose of drinking water well operation. 24-7 operation capable.
by
  • Recommended
Great pump for home well potable water needs and other operations where you need high water flow ...
Great pump for home well potable water needs and other operations where you need high water flow capacity. It's nice to keep a well pump as a spare because they always fail at the worst time. These Everbilt pumps are economical and great to keep at the cabin in case the primary pump quits on you. This is prewired for 115 and 230 volt input. Specs are as follows: Size 15.1 inches long 8.5 inches tall 7.9 inches wide 115volt draws 20 amps. 230 volts draws 10 amps. Simply flip the internal switch to 115V if needed, the pump is set to 230V from the factory. 1 inch FNPT discharge size Intake 1 to 1/14 inch 25 foot deep water level max Water flow rates at feet of head, 40psi. Max pressure 66psi: 0ft 7GPM 25ft 4.5 GPM Self priming after casing is filled with water initially. Do not run dry. Pressure gauge built in. Thermoplastic housing. 1 year warranty. These types of pumps work well for irrigation pumps and waterfall pumps as well as it's intende purpose of drinking water well operation. 24-7 operation capable.
by
  • Recommended
The Everbuilt line of shallow well pumps are reliable, easy to install, and work for many years. ...
The Everbuilt line of shallow well pumps are reliable, easy to install, and work for many years. We have been adding watering stations and have been using these pumps at each location. We always have a backup pump in the pump house incase there is ever an issue. The pump has 1-1/4" IPS pipe inlets. The pump does require priming before use. We usually add a stand-tube that we can add water into to get the pump going. Once she picks-up the water, we shut it off, remove the tube, and cap it off from the inlet. The pump provides a steady flow of water and has a pressure switch installed on each pump. You only need to have a pressure tank for the pump. The pump is a little noisy so you might want to keep this in mind if you are installing near a home that is occupied. But when you have it inside a pump house, it is not so bad.
by
  • Recommended
The Everbuilt line of shallow well pumps are reliable, easy to install, and work for many years. ...
The Everbuilt line of shallow well pumps are reliable, easy to install, and work for many years. We have been adding watering stations and have been using these pumps at each location. We always have a backup pump in the pump house incase there is ever an issue. The pump provides a steady flow of water and has a pressure switch installed on each pump. You only need to have a pressure tank for the pump. The pump is a little noisy so you might want to keep this in mind if you are installing near a home that is occupied. But when you have it inside a pump house, it is not so bad.
by
  • Recommended
Got this pump to use for a background water fall and pond. The project is still in the works so I...
Got this pump to use for a background water fall and pond. The project is still in the works so I don’t have pics of the finished project. I have a relatively small backyard and it has a gentle slope so what I’m planning will not require any digging. Just have to lay some underpayment down and place the rocks. Will only require a 1/2 inch pvc pipe from low end back to pump at high end. This pump will more than do the trick.
by
  • Recommended
This is a solid, well made jet pump designed for a specific purpose: Draw water from a potable w...
This is a solid, well made jet pump designed for a specific purpose: Draw water from a potable water well under 25 feet deep, and use it to fill and pressurize a tank that will deliver pressurized water for domestic use. My purpose is to draw irrigation water, and I have learned that there other pumps for that use. Opening the covers, it is straightforward to select the voltage, install the wiring and set the pressure desired. Be sure to select the correct voltage! At 120 volts it will consume a full 20 amps, so be sure to use the correct wiring. As my irrigation water is not available yet, I had to construct an "artificial well" to put it through it's paces. I ranked ease of installation as "good" because the steps to correctly pipe this pump are precise and must be followed carefully.
by
Response from AquaPro TeamAug 10, 2020
Thank you for the nice review. Please let us know if you have any questions on the kit. Our number is 844-241-5521.
  • Recommended
1 found this review helpful
Good pump
Good pump
by
  • Verified Purchase
  • Recommended
I am try to replace my old water well jet pump. In my barn. I am using my pump to feed my chicke...
I am try to replace my old water well jet pump. In my barn. I am using my pump to feed my chicken and water my garden. ..i do have 110 power out there..so it should not be a big deal for the Electrician to wire this up for me. I'm very pleased at how easy this is to set up. And I'm very excited to get my garden up and irrigated. My pump is inside the barn So the elements of the weather won't mess my new pump.
by
  • Recommended
Marketed as a shallow well jet pump, this pump could be used for irrigation systems or sprinkler ...
Marketed as a shallow well jet pump, this pump could be used for irrigation systems or sprinkler systems to pump water from a pond; however, is not suitable for being exposed to outdoor weather since the pump pressure line is clear nylon and not likely sunlight resistant; the pump must also be protected from freezing. It is not a portable pump, like some, and therefore requires hard-wired connections to the power inlet box; power can be 120 VAC or 240 VAC, selectable by the user. Adjustable pressure gauge is a nice feature; corrosion resistance to salt water or other chemicals in water is not known and not identified in the literature, so not likely suitable as a pool pump. Picture show pump as removed from box and accessories recommended for complete installation.
by
  • Recommended
We have an outdoor shower and we dug up and installed a shallow catch basin. It was driving the w...
We have an outdoor shower and we dug up and installed a shallow catch basin. It was driving the wife nuts because the mosquitos were breeding. So, it needed to be pumped out. So, upon my request my wife got this for me. Although it's way more power than needed it runs smoothly and relatively quiet. Pumps about 20 gallons almost before I can throw the switch back off.
by
  • Recommended
My review is actually for the 3/4hp pump. Similiar only more robust, and increase GPM capaacity/c...
My review is actually for the 3/4hp pump. Similiar only more robust, and increase GPM capaacity/capability. I have another everbilt, 1/2hp at my buddies propert, and after careful priming of the instalation, and carefully following the well defined instalation instructions. I have a pumping system that works flawleesly, and is qieter than I expected. You will not be disapointed.
by
  • Recommended
My review is of the Everbilt ¾ HP shallow well jet pump. I use this pump for something other th...
My review is of the Everbilt ¾ HP shallow well jet pump. I use this pump for something other than what it was originally intended, to remove water from my hot tub. In the past I would siphon or use the drain to remove water. Both these methods were slow and I had little control on where the water went. With this pump I can quickly drain off some water or empty the hot tub and the water goes exactly where I want it. I chose this pump because it has a good volume and is not too big or heavy to handle. Excellent solution for my needs. The pump was very well packaged. Seems to be well manufactured and assembled. It was easy to get the fittings I needed to accomplish the plumbing connections I required. It comes with complete instructions for installation and use. I am totally pleased with this pump.
by
  • Recommended
This Everbilt 3/4 HP Shallow Well Jet Pump seems to be very well made. Its a good size so fits i...
This Everbilt 3/4 HP Shallow Well Jet Pump seems to be very well made. Its a good size so fits in a small foot print so you don't need a large area to set up. It is labeled really well so you will always be able to see what size pump it is. The instructions are well written, showing how to install this shallow well jet pump in a well point installation or a cased well installation both with pictures to help make it very understandable. The pump runs really quiet, much quieter than the old pump we replaced .
by
  • Recommended
I realize now that the Everbilt 1/2 HP Shallow Well Jet Pump is a pump for real wells only. I tho...
I realize now that the Everbilt 1/2 HP Shallow Well Jet Pump is a pump for real wells only. I thought with a small man-made pond, I could install this pump to create a water fountain feature. Now that I received the pump and have read through the instructions and guidance I can see that the pump requires a minimum depth of 5ft. This would work great if I had a well.
by
  • Recommended
Works great! This 1/2 HP shallow well jet pump is well made and easy to install, with clear and e...
Works great! This 1/2 HP shallow well jet pump is well made and easy to install, with clear and easy to follow instructions. The body, being thermoplastic, is corrosion free and will be a blessing as we live in an extremely humid area. It has a good sized pressure gauge which is easy to read and the pump is reasonably quiet in operation. The motor is fan cooled and has an overload protector to prevent overheating. While the pump is self-priming, be sure to fill the housing before first use. All in all, this unit is well made, of good quality and a very good value for it's price.
by
  • Recommended
I wanted to use a pump for pulling water out of our yard. I know this is a shallow well pump but...
I wanted to use a pump for pulling water out of our yard. I know this is a shallow well pump but felt it cold help in this case. The pump worked like a charm 1. Constant pressure on the pump to pull water 2. Pulls water up out of a hole we have that is almost 9 feet down 3. The pump continued to pull until I stopped the pump - this was one thing a different pump would be better It is a very powerful pump I would recommend that you add the support tank to maintain pressure and water seal - this will really help the unit stay primed
by
  • Recommended
If you have an existing installation this Everbilt shallow well jet pump should easily install wi...
If you have an existing installation this Everbilt shallow well jet pump should easily install with your existing fittings. We got this pump for a new use so we did have to pick up some additional parts to set it up. I've included photos of info from the included instructions that indicate additional requirements. We've been happy with Everbilt pumps in the past. This one also appears to be made well.
by
  • Recommended
Everbilt makes good products and this Shallow Well Pump is a great example. The thermoplastic ca...
Everbilt makes good products and this Shallow Well Pump is a great example. The thermoplastic casing prevents rust and corrosion. There is a choice of two voltage selections which are selected with the flip of a switch. The instructions are very complete and consist of 3 different guides and include a list of tools and supplies needed to install the pump as well as a list of materials that are not included. This pump is for wells 5 - 25 ft deep.
by
  • Recommended
The Everbilt 1/2 HP shallow-well jet pump is made of fiberglass reinforced thermoplastic, which m...
The Everbilt 1/2 HP shallow-well jet pump is made of fiberglass reinforced thermoplastic, which makes it corrosion resistant. This is a great feature especially for damp/humid areas. The unit comes pre-wired for 115/230-Volt operation, and is factory pre-set at 230-Volt. It has a fan cooled motor which is a great feature because it extends the life of the motor, and has a thermal overload protector to prevent overheating. The pumps is supplied with a 30/50 pressure switch for automatic operation, and a pressure regulator for performance monitoring. The jet pump is self-priming after the initial housing is filled with water which is a great feature. The pump is ready to install to your existing fittings and is designed for wells of 25 ft. or less. A good solid pump made of high quality materials. Very good pump for the price point.
by
  • Recommended
We selected this EVERBILT 1/2 HP SHALLOW WELL JET PUMP as this pump appears to be well built and ...
We selected this EVERBILT 1/2 HP SHALLOW WELL JET PUMP as this pump appears to be well built and well made and would be a good replacement for an old aging water pump thart we have had in place for a great number of years; installation of this EVERBILT 1/2 HP SHALLOW WELL JET PUMP was fairly simple, especially since they have complete instructions included along with the warranty book; this EVERBILT 1/2 HP SHALLOW WELL JET PUMP was easy to start up and is working well - just remember to follow the instructions provided; based on what we have seen and experienced, we highly recommend this EVERBILT WELL JET PUMP
by
  • Recommended
This Everbilt 3/4 HP shallow-well jet pump is perhaps the smartest design of any pump I’ve ever u...
This Everbilt 3/4 HP shallow-well jet pump is perhaps the smartest design of any pump I’ve ever used. The key is the fiberglass reinforced thermoplastic that it’s made from, which is very corrosion resistant. Corrosion is one of the things that make pumps die prematurely. It is also self-priming and has a fan-cooled motor. It comes preset from the factory for 230-Volts but will run off either 115 volts or 230 volts. If you want to operate the pump on 155 volts, you simply loosen a cover, flip the switch from 230V to 115V and then replace the cover. Simple! There is a 30/50 pressure switch on the pump already for automatic operation and a pressure regulator to monitor performance. This is a shallow well pump and therefore is designed for wells with pumping levels of 25 feet or less. It comes ready to install. Personally, I love Everbilt products.
by
  • Recommended
This pump is well made and features a simple switch to wire with either 115 volt or 230 volt wiri...
This pump is well made and features a simple switch to wire with either 115 volt or 230 volt wiring. It is pre-assembled with a pressure switch and only requires the electric wire, pressure tank, foot valve and piping. A helpful list of all required items is included on the outside of the packaging. If you are in a cold weather area, be sure to protect this pump from freezing as the plastic pump housing may be more susceptible to cracking. The pump does require priming to work, so be careful not to run it dry. The maximum lift for this unit is 25 feet. It is great for an irrigation pump where you can draw from a pond or creek.
by
  • Recommended
Showing 1-30 of 578 reviews

Frequently Bought Together

Best Seller
+
+
Price:
$309.00

Compare Similar Items

current item

Housing Material

Thermoplastic

Cast-Iron

Cast-Iron

Cast-Iron

Impeller Material

Thermoplastic

Thermoplastic

Thermoplastic

Thermoplastic