Questions and Answers for KRAUS Loften 33 in. Drop-In/Undermount Single Bowl 18 Gauge Stainless Steel Kitchen Workstation Sink with Accessories

A:  It fills the entire bottom of the sink

A:  Hi Skro, Thank you for reaching out, I can answer that for you. The bottom grid that is included with this model sink measures 30" x 16 5/8" Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Overall the grid is 30.5” x 17”.  The grid openings vary, but most of them are about 1” x 2”. 

A:  Thank you for reaching out, this model sink comes with a cutout template with the proper cutout dimensions. Every model sink has unique cutout dimensions that are required, and this is due to the length, width, and corner radius. Because of this, each sink has a unique cutout that is not shared by other model sinks. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hey Jammy, Thank you for your interest in our kitchen sink, I can answer your inquiry. This model sink when installed as an undermount, has the faucet hole pre set at the back lip, you will cut the hole through your counter at the faucet hole location. Please contact our customer service at 1-800-775-0703 or customerservice@kraususa.com if you’d like to continue the conversation.

A:  You have to have 48" or larger base cabin under the sink to have room for the garbage disposal .

A:  Hello Jane, Thank you for your inquiry, I can answer that for you. If you would like to install a disposal unit you can replace the strainer that was included with the sink and install the disposal directly to the sink drain opening, all disposals are installed this way. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Suzs, That is a great question and I can answer that for you. The accessory hole for this model is measures 1 3/8" in diameter. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hello Susana, Thank you for reaching out, I can answer your question. We do not recommend the creation of additional holes into your sink as it could decrease the structural integrity of the sink. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hello Steven, thank you for reaching out, that is a great question and I can answer that for you! In order to determine the exact countertop cutout specifications you would need to refer to either the template that comes with the sink or the sinks DXF file. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hello Steven, thank you for reaching out, that is a great question and I can answer that for you! In order to determine the exact countertop cutout specifications you would need to refer to either the template that comes with the sink or the sinks DXF file. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hello Tomm, Thank you for reaching out, I can answer your inquiry. We don't make this exact sink with the drain on the right. We do make other sinks with the drain on the right so please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.

A:  Hello Ruby, Thank you for reaching out, I can answer your inquiry. We do not recommend the creation of any additional faucet or accessory holes in the sink as it can reduce the structural integrity of the sink itself. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions.