Questions and Answers for Simpson Strong-Tie H2.5A 18-Gauge ZMAX Galvanized Hurricane Tie

A:  Hi Gardener, this is Colin from Simpson Strong-Tie. The overall height of the H2.5AZ is 6". This tie provides a positive connection between truss/rafter and the wall of a structure, or a deck joist over top of a beam to resist wind and seismic forces. If you need more information or have additional questions, please contact the Simpson Strong-Tie Customer Service team at 800-999-5099. Thank you.

A:  Dawn, this is McKenzie from Simpson Strongtie. The H2.5A is reversible so no need for a left and right. Thanks.

A:  Hey Angel, Ricardo here with Simpson. These look the same in appearance, but are different in length, hole pattern, and published load values. Please contact our Technical Support team at (800)999-5099 to discuss further if needs be.

A:  Hello Todd, this is Ricardo with SImpson. The suggested fastener for the H2.5A is a 0.131 x 2.5" nail. If you go with the shorter N8D5HDG-R, which is a 0.131 x 1.5" nail, it will change the uplift load capacity of the hurricane tie. If you would like to discuss this further, please contact us at (800)999-5099

A:  yes

A:  Yes with the right screws for metal

A:  ​Hi, thank you for your message. This is Ricardo with Simpson Strong-Tie. Unfortunately, the H2.5A is only for wood-to-wood applications. For steel (CFS) applications I would recommend you take a look at the S/H2.5 which is designed specifically for steel application connections with #10 self-drilling screws. If you need more information or have additional questions, please contact the Simpson Strong-Tie Customer Service team at 800-999-5099. We look forward to hearing from you.​​

A:  Simpson Strong-Tie #9 x 1-1/2-in Mechanically Galvanized Strong-Drive SD Exterior Wood Screws

A:  Hi Jeff, this is Colin from Simpson Strong-Tie. Thank you for your inquiry. The H2.5A can be installed with our Simpson Strong Drive (SD) Connector Screws. The required size is our #9 x 1 1/2". Item # SD9112. If you need more information or have additional questions, please contact the Simpson Strong-Tie Customer Service team at 800-999-5099. Thank you.

A:  #10 x 1-1/2 in. 1/4-Hex Drive, Strong-Drive SD Connector Screw

A:  I believe you can use the #9 x 1-1/2 in. 1/4-Hex Drive, Strong-Drive SD Connector Screw for that tie.

A:  ​Hi Scott, this is Colin from Simpson Strong-Tie. Maybe, but you'll need to check with the building designer when it comes to replacing specified products. The H2.5A is a hurricane tie that provides a positive connection between the truss/rafter and the wall of the structure to resist wind(uplift) and seismic(F1 & F2 lateral load). The A23 is an angle that can be used to make a wide range of 90 degree connections and resists seismic (F1 and F2) lateral loads. If you need more information or have additional questions, please contact the Simpson Strong-Tie Customer Service team at 800-999-5099. Thank you.

A:  They don't really hold any load. They are commonly referred to as hurricane ties acting to tie the floor rafters/ roof truss to the wall to prevent uplift during a high winds. They are not an alternative to LUS26

A:  Hi , This is Ricardo with Simpson Strong-Tie. You can view load information by going to the product homepage for the H2.5A on our website. You can reference that page by clicking the link below. https://www.strongtie.com/seismicandhurricaneties_strapsandties/h25a_htie/p/h25a#LoadTables If you have any further questions our Customer Service team is available to talk with you directly and take you through a step-by-step solution. Please call us at 800-999-5099. We look forward to hearing from you.​

A:  They aren’t made for holding load.