Buffalo Tools 2 in. x 18-Gauge Strip Finish Nailer-DISCONTINUED-ANFIN at The Home Depot
Free shipping
Discontinued

Buffalo Tools

Model # ANFIN

Internet # 100670928

2 in. x 18-Gauge Strip Finish Nailer-DISCONTINUED


Buffalo Tools 2 in. x 18-Gauge Strip Finish Nailer-DISCONTINUED
 

This item has been discontinued.
The Home Depot no longer carries this specific product.

$25.97 / each
Item cannot be shipped to the following state(s): GU,PR,VI

PRODUCT SOLD Online Only

In Stock

Loading...

PRODUCT OVERVIEW

Model # ANFIN

Internet # 100670928

Make your projects look professionally finished with the Buffalo Pneumatic Nail and Staple Gun. Don't dent and chip the surface of the of your expensive, high quality lumber by driving nails in by hand. Use our Pneumatic Nail and Staple Gun to cleanly drive nail heads below the surface of the wood, saving you time and improving the quality of your work. The Buffalo Tools 2 in. 18-Gauge Finish Nailer can fit into tight spaces like corners and closets when you are installing baseboards, crown molding and door casings. This Finish Nailer can hold up to 100 brad nails per coil.

  • Great for general purpose carpentry work
  • Rubberized handle for a comfortable grip
  • Lightweight, 3 lb. design
  • 100 brad capacity
  • 55-95 psi operating pressure
  • 1/4 in. NPT inlet
  • Includes oiler bottle and 2-hex key
  • Storage case included

SPECIFICATIONS

Air Tool Type  Air Nailer  Assembled Depth (in.)  8.56 in 
Assembled Height (in.)  1.44 in  Assembled Width (in.)  9.1 in 
Cordless/Corded  Cordless  Energy Type  Air 
Fasteners included  No  Loading type  Strip 
Maximum Fastener Size  2 in  Maximum fastener size (in.)  2.0 
Minimum Fastener Size  3/8 in  Minimum fastener size (in.)  0.375 
Nail Gauge  18  Nailgun Angle 
Reconditioned  No  Returnable  90-Day 

CUSTOMER REVIEWS

Rated 4.6 out of 5 by 55 reviewers.
Rated 5 out of 5 by Great nail gun! This is a great nail gun. I wanted something inexpensive to make a few projects easier and looked at quite a few that were under $50. I decided on this one because it: looked EXACTLY like a few that were more expensive (hinting to the difference being branding); 2" brad capacity; protective case; adjustable depth control; and price. The nail gun works like a dream. Only one jam and it was easy to clear. It can easily shoot a 2" brad through hardwood with a good brad. Must use pressure at top of range for that. But, 55-60 PSI works great for 1.5" brads in baseboards and moldings. The only drawback is that the 'depth control' is set by you externally regulating pressure...there is no gun control for depth. June 5, 2011
Rated 4 out of 5 by ok for the homeowner Received tool on time. Coming with a case is a plus. Did include some start up nails. User manual was not with the tool and was not available on line. Had to get it emailed from the importer. User manual barely useful. Have used the gun to install new finish work in a bath. So far with limited use, performed fine. Running on a 3 gallon compressor @80 psi with no problem. July 10, 2012
Rated 4 out of 5 by great little finish nail gun I have a small project in the basement. I install T&G pine on the ceiling. (I ripped the suspended ceiling in a moment of anger out). In the store the finish nailer cost all about $ 100 I was horrified. I ordered this gun and use it to put a 1 3/4 inch braid into the pine. It works great. The tool is very light weight. The only problem I have is that the tip is big and I have to turn the tool 90 deg. around to have access to the groove. Also the safety is in front of the tool and the nail comes out about 1/4 behind. I had to get used to that. I think the spring for the safety is to strong and can scratch or dent the wood. There is not jam release. I had no jams yet... I noticed that the tool can make dents into the wood. April 18, 2013
Rated 5 out of 5 by Great buy. Great performance. I wanted an inexpensive brad nailer with two inch capability for a small renovation project (approximately 300 brads) for tongue and groove pine board paneling and window trim. I've used it a couple additional times, too. I am very satisfied, No jams, no misfires. At about $33 including case, tax and shipping it was a real bargain. I used Porter Cable brads because of problems reported with other nailers (not at HD). It does leave a hardly noticable dimple in softer wood. Long term durability is unknown, but at this price I consider it paid for already. December 26, 2012
Rated 4 out of 5 by GOOD, LOW COST FINISH NAILER I needed a good, low cost finish nailer for a small project I am doing. Mostly attaching baseboard trim. Since I am not a builder by trade nor do I plan to do a lot of projects that require a finish nailer, I didn't want to spend a lot of money on a tool that I won't be using much. To rent one for a week didn't make much sense when this unit is available at such a low price. This tool works great. I did have to order a second one, as the first one I received had an air leak that didn't allow the pressure to actuate the gun. As always, Home Depot was great in arranging the return of the defective unit and shipped out a replacement right away. The Home Depot customer service is excellent, this tool is more than satisfactory. I would recommend it to anyone. August 3, 2009
2 3 4 5 6 >>

SHIPPING AND DELIVERY OPTIONS

Standard Shipping includes delivery by small parcel service. Processing time varies by product.


Orders for this item may be expedited for an additional fee.


Other Delivery Options:

Express and Expedited shipping options are also available. Estimated arrival times are available in checkout.


If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.