Q:Has anyone tryed it on electrical PVC schedule 40 or 80?
by|Apr 6, 2019
1 Answer
Answer This Question
A: I haven't tried it. But from experience with using other heat guns, I would not expect it to work. It puts out about the same heat as a corded heat gun on low. It is enough heat to make minor adjustments to an existing bend, but not enough for a new bend.
If you are going to do much bending, invest in a heating blanket, or heat box. They will pay for themselves is labor savings.
by|May 2, 2019
Q:genarally how long would the battery last?
by|Feb 26, 2019
2 Answers
Answer This Question
A: Using it 6 hours a day, hold charge for 2 days with M18 5.0 battery
by|Apr 4, 2019
A: too many variables involved to provide run-time based on the batteries we offer.
by|Oct 31, 2023
1 found this answer helpful
Q:What type of heating gun do I use for working with TOO
by|Dec 15, 2018
2 Answers
Answer This Question
A: para despejar plastico de las unidades
by|Mar 11, 2019
A: need more information
by|Dec 17, 2018
Q:What is the heating element? (what kind of heat?)
by|Oct 24, 2018
2 Answers
Answer This Question
A: ceramic coil
by|Dec 9, 2018
2 found this answer helpful
A: The heating element is a high-performance heating coil.
by|Mar 11, 2019
Q:Will this heat up the inside of a car in cold weather on a single charged battery?
by|Sep 6, 2018
5 Answers
Answer This Question
A: No. That is not the intended purpose and is probably very unsafe.
by|May 21, 2021
1 found this answer helpful
A: I wouldn't think so it only runs for about 9 minutes on a fully charged 5 amp hour battery
by|Dec 17, 2018
A: Not recommended and I would not recommend it for use as a hair drier either.
Next...
by|Jan 18, 2024
3 found this answer helpful
A: since this tool is not meant for that kind of use .i cant answer your question..
by|May 21, 2021
A: no, we would not recommend it for this type of application
by|Jan 3, 2021
2 found this answer helpful
Q:I want 350 deg C temperature , it's possible??
by|Aug 16, 2018
4 Answers
Answer This Question
A: This unit will reach temperatures as high as 875 F.
by|Dec 6, 2023
2 found this answer helpful
A: 351* F is the hottest I got it (advertised as 875* F being max). So I would say it is not possible.
by|Dec 6, 2023
2 found this answer helpful
A: max temp output is 875
by|May 5, 2023
A: Since 350 deg C is equal to 662 deg F, and the stated max temp is 875 deg F (468.3 deg C), then it should. At least give it a try. You could always take it back to the store.
by|Mar 10, 2023
1 found this answer helpful
Q:Im in the HVAC field and I wonder how well this will work to melt ice off of frozen evaporator coils?
by|Dec 16, 2017
5 Answers
Answer This Question
A: It works about as well as a hair dryer. If you don't have a lot of ice to melt, it will work. For a major blockage, you are still better off with a forced air space heater. Your arms will than your.
by|May 2, 2019
A: You Will Alleviate Your Stress With This Heat Gun always ready to go
by|Aug 13, 2020
A: yes i could see that working even though i haven't tried it .. , i sometimes use it to heat air lines that have frozen on heavy machinery i work on out side in the winter
by|May 6, 2023
A: Dunno how well is measured....but hot vs cold, Im sure it will melt but sure beats carrying an extention cord
by|May 5, 2023
A: this unit can produce a temp of 875F and depending on the amount of ice, this application could be time consuming.
by|Feb 23, 2021
6 found this answer helpful
Q:Has anyone used this to bend conduit? Is it worth it to have the cordless? I have lots of batteries..
by|Nov 15, 2017
2 Answers
Answer This Question
A: It is definitely worth it to have a cordless heat gun so you can go where you need to go without a cord
by|Mar 11, 2019
1 found this answer helpful
A: no, this heat gun is not for bending conduit
by|May 5, 2023
2 found this answer helpful
Q:can it be used to heat pvc pipe on a solar field site?
by|Oct 26, 2017
2 Answers
Answer This Question
A: Yes, you can heat PVC with this tool, you need to supply the battery as this is a tool only
by|May 5, 2023
A: It does not last long and the airflow is much limited compared to an AC powered heat gun. For a large PVC bending, I would use an AC and generator over this. Much faster heat transfer and the job would go much faster.
by|Mar 11, 2019
2 found this answer helpful
Q:Is the Milwaukee 49-80-0300 nozzle kit compatible with this heat gun?
by|Oct 21, 2017
2 Answers
Answer This Question
A: No. It is an over priced piece of junk. Basically a Harbor Freight grade Power Tool ten times the price because its Red and Black and says Milwaukee on it. The specs and capabilities arent mearly as good ss any other heat gun that js GREATLY more affordable.
by|Mar 11, 2019
1 found this answer helpful
A: Yes, the 49-80-0300 is compatible with this heat gun (2688-20).