Questions and Answers for Rev-A-Shelf 19 in. H x 20.75 in. W x 22 in. D Base Cabinet Pull-Out Chrome 2-Tier Wire Basket

A:  A drill/driver would be a big help.

A:  You will need a drill to make pilot holes for the mounting screws.

A:  It is not necessary, but can assist in the installation.

A:  You can use a drill or screw driver if you like. It will take 20-30 min.

A:  Thhey can't be installed seperately, but if you buy the 5WB1-0918-CR this is the single version and not the double.

A:  Not really but they do make one for trash cans as well.

A:  No, they cannot be installed separately.

A:  Yes they can be installed separately.

A:  They can't be installed independently as I mentioned in the other question, you need the 5WB1-0918-CR. This unit can then be installed with 4 screws to the bottom of the cabinet. You actually could side mount these but you would have to detach some parts and then that would void the warranty.

A:  only if you cut the supports and buy more anchoring.

A:  No, they use a frame whichmakes installation much easier and assures that the baskets are installed level. They can't be seperated and used individually.

A:  Yes, these units are full extension drawer glides with a built in basket. If you are familiar with installing drawer glides, you will not have a problem. The basket portion of this assembly is removable if needed.

A:  Yes, this model can be used separately and also can be side mounted.

A:  You can fit the 20.75'' model.

A:  Yes, it will fit perfectlly!

A:  Yes the outside to outside dimension is 20.75, but the part that slides in and out is only 20.25" so your opening is large enough.

A:  the opening is 24 inches.

A:  It really depend on the size of the cabinet door opening rather than the size of the cabinet. Once you know your cabinet door dimensions pay close attention to the minimum requirements on the rev a shelf installation instructions. When they say the minimum opening is 13.5 they mean it. If the cabinet door opening is smaller than what rev a shelf recommends, well, things probably won't work as designed (smooth slide and soft close). Learned that the hard way.

A:  If you are saying you have a B24 which is a 24" outside to outside width of 24" I would only have to assume that you have a 21" opening. I recommend the version you have chosen which is 5wB2-2122-CR

A:  Is this the size of the opening or the inside measure? You must have a 21" opening width that is at least 19" high. If your OPENING is 24" wide, just use this 20.75 in. and use the extra space for cookie sheets.

A:  We don't offer in a 20" depth in the 14.75" version but we do in the 11.75" version. 5WB2-1218-CR. It is only 18" deep not 22"

A:  Please check the Home Depot website.

A:  I don't know - you would have to look at the website.

A:  Hi Tommy, Check out the Rev-a Shelf website. You will find all their selections and sizes there. https://www.rev-a-shelf.com/

A:  By other dimensions I assume you are asking about minimum openings. This requires a 14.5" or larger opening.

A:  Yes but you can screw a board lengthwise in your cabinet and attach the tracks to the boards. They attach at the side and the bottom of the tracks.

A:  10 inches wide is kind of a "off" number for standard cabinetry. Plus from the way this is worded we can't tell if you have a 10" wide cabinet or a 10" wide opening. That being said, this is designed for a 12" wide cabinet with a 9" opening, so you could just center and mount it on the bottom and the back and not worry about the sides. You could also insert shims into your cabinet for your side mounts to adhere to but that's up to you and how much work you want to put into it.

A:  No, you will need to secure it to the floor and to the side of the cabinet. I put a thin piece of wood between the shelving unit and the cabinet, maybe 3/4" thick. This was to make it sturdy and not hit the side of the cabinet when opening.

A:  Again, check the website.

A:  According to Rev-A-Shelf web site it weighs 24lbs. Hope that helps