Questions and Answers for BEHR PREMIUM 1 gal. Deep Tint Base Low Lustre Interior/Exterior Enamel Patio and Floor Paint

A:  Hi John, Thanks for writing in with your question. Yes, our Porch and Floor Paint is manufactured in a quart size. I recommend checking with your local store for availability. Have a great day! Regards, Giovanna

A:  As far as I know there is no quart size that I have seen made.

A:  I hosed my front porch off (pollen) 3 days after painting and it was fine

A:  Hi LS300, Thanks for your question! We recommend allowing the paint to dry for at least 24 hours before the coating is exposed to rain or heavy moisture. Best of luck with your project! - Sara

A:  This can be used on concrete, laminate, vinyl, and wood.

A:  Hi Bill, Thanks for writing in. We do not recommend using the Porch & Patio Floor Paint on fiberglass. It's best to work with the Home Depot to see if they can make a product recommendation for your new fiberglass door. Best wishes! ~Takhari

A:  Hi tom, That’s a great question. The Low-Lustre Exterior Porch and Patio Floor Paint is tintable to safety yellow and available in a 5-gallon container. I hope this information helps and good luck on all your future projects. Roxana N.

A:  Hi Tom , I not sure check with your local Home Depot Paint department

A:  Hi, TF. The Porch & Patio Paint can be used on your fence. Just make sure that you properly prepare the surface and make sure it's clean, dry, and primer before applying the paint. I hope this helps - Vince

A:  No, this can not be used on a wood fence.

A:  Hi, 158. I wouldn’t be able to answer that, as I wasn’t there to monitor your project. However, feel free to give us a call at 1(800) 854-0133 extension 2 and we’ll be sure to help you out best we can. I hope this helps - Vince

A:  I not exact sure why you have dark blotch streaks if I would guess maybe it needed to be scrap and down before I would recommend visiting your local home depot and speak to the expert in that department

A:  Hi, Mary. The Porch & Patio Floor Paint should dry for at least 48 hours for light foot traffic and 72 hours for heavy foot traffic. If you have any other questions, feel free to e-mail us at webtechserv@behr.com and we'll help you out. Good luck with your project - Vince

A:  I used it on my front porch. I waited 24 hours to apply the second coat and walking on it was no problem. Directions say to wait 72 hours for normal use

A:  Hello, Thank you for your interest in our products. We would not recommend driving on the coating the next day. Doing so could potentially cause the coating to peel. We recommend waiting a minimum of 7 days before driving on the coating and after the 7 days, we suggest parking the wheels on cardboard for an additional 3 days for longer dry time. Best regards, Kevin

A:  I would not recommend on driveway or garage. The tires and consistent traffic would peel and remove the paint. It's for foot traffic only. I would recommend the garage one part epoxy for your garage. Can be colored and safe for driving after a couple days of drying.

A:  I use BEHR Premium 1 Gal Concrete and Masonry Bonding Primer for Interior for outdoor/Interior KILZ adhesion bonding primer

A:  Hi, jenutah. For concrete floors, I would recommend our Masonry & Concrete Bonding Primer. Just ask your local Home Depot associate to help you find it, and they should be able to point you in the right direction. Hope this helps - Vince

A:  If you one coat 1 Gal if you need two 1 gal and 1/2

A:  Hi Pat, Thanks for writing in with your question. You will need two gallons of paint to apply two coats to your patio. If your concrete is uncoated, make sure to clean it, etch it and prime it with the Concrete Bonding Primer, (No. 880) before painting it. Good luck with your project! Regards, Giovanna