J-B Weld Waterweld-8277 - The Home Depot

J-B Weld

Model # 8277

Internet # 202528473

Store SKU # 420496


J-B Weld Waterweld

This item has been discontinued.
The Home Depot no longer carries this specific product.

$5.77 / each


Model # 8277

Internet # 202528473

Store SKU # 420496

The J-B Weld Co. 2 oz. WaterWeld Epoxy Stick helps make repairs in moist applications and underwater applications. This epoxy adheres to a variety of surfaces including fiberglass, PVC plastic, copper, iron and aluminum.

  • Helps to make repairs in moist applications and underwater applications
  • Adheres to a variety of surfaces including fiberglass, PVC plastic, copper, iron and aluminum
  • Can be drilled, sanded, filed, tapped, machined and painted
  • For general-purpose repairs
  • Cures in 60 minutes


Assembled Depth (in.)  1.1 in  Assembled Height (in.)  7.5 in 
Assembled Width (in.)  3.9 in  Product Depth (in.)  1.1 
Product Height (in.)  7.5  Product Width (in.)  3.9 in 
Adhesion level  Medium to high  Adhesive Product Type  Adhesive Putty 
Drillable  Yes  Flammable  Yes 
Hazardous Code  Cannot Ship Air.  Indoor/Outdoor  Indoor/Outdoor 
Moisture Resistant  Yes  Paint Product Type  Glue and Epoxy 
Product Weight (oz.)  2 oz  Recommended surfaces  Ceramic,General Purpose,Multi-Surface 
Sandable  Yes  Solvent resistant  Yes 
Stainable/Paintable  Stainable & Paintable  UV/sunlight resistant  Yes 
Warranty / Certifications
Manufacturer Warranty  n/a 


Rated 3.5 out of 5 by 11 reviewers.
Rated 4 out of 5 by Shower fix First, wear gloves when mixing. I did not and I now have no fingerprint on my thumb and index fingers. Second, I used this to patch a hole in a fiberglass shower/tub insert. I practiced first and found the trick to this is mix until you think its mixed, and then mix for another minute or two. It wasn't as pliable as joint compound, but also not as runny as liquid epoxy. Sanding was easy from 120-220-400. It matched the color of the insert better than any paint did. November 10, 2014
Rated 5 out of 5 by inground pool leak I had a pool drain leak & didn't want to drain it so with a stick of Waterweld and my driving gear it was easy! Thanks Waterweld! The Pool Boy June 12, 2012
Rated 5 out of 5 by The best for my purposes I use it for patching holes in polystyrene molded products.. I like it because it dries as quickly as I need, 25-30 minutes. Can sand or drill after an hour and it is very easy to use in small amounts. June 22, 2014
Rated 5 out of 5 by Saved me alot of hassle The main PVC stack in my house developed a slow leak at the clean-out joint that would have required cutting out a section and splicing in a whole new PVC joint in a tight area behind a hot water heater, between studs and with sheet rock on one side. I used this waterweld epoxy stick to close the leak. It was easy to work with, works quickly, and appears to have bonded nicely with the PVC. At any rate there is no more water on my furnace room floor. October 24, 2011
Rated 5 out of 5 by Sealed up a leaky pvc Had a leaky condensation PVC elbow from the AC in my attic. This did the trick to stop the leak, so I didn't have to reconnect a new elbow. September 17, 2013
2 >>


Store Exclusive. This item is available for purchase in select stores only.