Free Shipping and BOPIS


Model # 80

Internet # 100174709

Store SKU # 615234

19 oz. Rubber and Vinyl Spray Adhesive

This item has been discontinued.
The Home Depot no longer carries this specific product.

$13.97 /each


Model # 80

Internet # 100174709

Store SKU # 615234

The 3M 19 oz. Rubber and Vinyl Spray Adhesive in aerosol form is fast drying and fast bonding. The adhesive resists plasticizing oils and bonds to most rubber and supported vinyl. The aerosol spray is low misting and allows for precise spray control for convenient application.

  • Can be sanded and drilled and bonds most rubber and vinyl
  • Aerosol spray is low misting with precise spray control
  • Resists plasticizing oils
  • Sets in 60 minutes
  • Neoprene-based contact adhesive bonds and dries quickly
  • High temperature resistance of up to 200°F (93°C)
  • Click here to view the Adhesive Spray Selector Guide

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.


Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
3 in 
Adhesion level 
Medium to high 
Adhesive Product Type 
Curing time (hours) 
Dries clear 
Glue/epoxy type 
Moisture Resistant 
Product Weight (oz.) 
19 oz 
Set Time (Min.) 
Solvent resistant 
UV/sunlight resistant 
Warranty / Certifications
Manufacturer Warranty 
Call for Warranty Information 1-800-328-6276 or 1-800-3M-Helps 


Rated 4.4 out of 5 by 13 reviewers.
Rated 5.0 out of 5.0 by Very Strong, Hi-Temp Rubber & Vinyl Spray While replacing a van headliner I ran out of Performance Hi-Temp Spray Adhesive. Ordering Performance brand by mail would take days and I wanted to finish the job. I always wanted to try the high temp 3M-80 and Home Depot carried it. In the end, the 3M Adhesive-80 is almost identical in every way, light wide web spray, super high strength and the only other spray adhesive that handles Florida sun. I've tried a number of different adhesives and so far, 3M 80 Hi-Temp and Performance Hi-Temp Trim Spray are the best, hands down. BTW, the key to replacing a headliner is cleaning off the old foam with a dry scrub brush. If it's not clean, no glue is going to save you. May 15, 2012
Rated 4.0 out of 5.0 by Excellent The adhesive is a good product, but it needs a better applicator like the one WD40 has - a straw. It does, however, take a long time to dry. August 29, 2015
Rated 5.0 out of 5.0 by 3m Spray Glue Anything with the 3m brand is far superior then the competition. I used this glue on my DeWalt orbital sander to hold the rubber disk in place after the disk fell off. I do a lot of sanding and 3m is the way to go. August 25, 2015
Rated 4.0 out of 5.0 by Does what it says I used this product to attach vinyl covers to some drawing desks and it worked pretty good. Did a couple of test pieces with different adhesives and this one came out on par with an old can of contact cement that I can't find anymore. this product has the advantage of coming in a spray can too so minimal cleanup/ no rollers or brushes needed etc. I tested the 3M 90 spray adhesive too and the 80 had a much higher adhesion for the vinyl that I was using. This product cures stronger over time. I was a little disappointed at first as the corners were a little too easy to pull up but after a week they were on there pretty good. June 23, 2015
Rated 5.0 out of 5.0 by Great Adhesive Easy to apply, and is a great adhesive. Works great for laminates, and almost any other thing that you want to apply to a surface. June 2, 2015
Rated 5.0 out of 5.0 by Good low temp adhesive. Initially used this for a higher temp application. Held well for about 1 year so I had to move to another adhesive. But applying this and set up was very easy. Keep some mineral spirits on hand to clean up any over lap or dripping. Would suggest laying object to be sprayed on a backing 2X its size. This way you can make smooth sweeping motions when applying. Just like spray painting. Should have good results. April 14, 2015
Rated 4.0 out of 5.0 by I fixed my sagging headliner I verified in a test area that this adhesive would not adhere to the dried out dusty foam rubber between the headliner panel and the vinyl on my '98 Saturn. So I removed the interior trim pieces, the sunvisors and the grab handles. This allowed me to remove the entire headliner panel. I scraped off the desiccated foam rubber from half the panel and spray glued it, then did the other half. There was not enough left to finish the tabs that folder over the top, but there would have been had I not waisted some on my test area. January 7, 2014
Rated 1.0 out of 5.0 by It's very bad i like that it was spray but really it's very weak February 25, 2015
  • 2015-09-02T11:23:56.451-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_13, tr_13
  • loc_en_US, sid_100174709, prod, sort_default
2 >>