0008925067634

Diablo

Model D0760R

Internet #100627136

Store SKU #618952

7-1/4 in. x 60-Tooth Fine Finish Saw Blade

$19.97 /each

Frequently Bought Together

Product Overview

Get fast, accurate cuts in wood and plywood. The Diablo 7-1/4 in. x 60-Tooth Fine Finish Saw Blade contains Perma-SHIELD non-stick coating to protect against heat, gumming and corrosion. The blade was constructed from TiCo high-density carbide for durability and strength.

  • Cuts wood and plywood cleanly and accurately
  • 5/8 in. laser-cut arbor for accurate blade rotation
  • TiCo high-density carbide to increase performance and maximum cutting life
  • Laser-cut heat expansion slots for true and straight cutting
  • Perma-SHIELD non-stick coating for protection against heat, gumming and corrosion

Specifications

Dimensions

Details

More Products With These Features

Search

Customer Questions & Answers

28 Questions95 Answers

Customer Questions & Answers

7-1/4 in. x 60-Tooth Fine Finish Saw Blade
7-1/4 in. x 60-Tooth Fine Finish Saw Blade

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
2 answers

3/4 Melamine

This question is from 7-1/4 in. x 60-Tooth Fine Finish Saw Blade
Asked by
Read all my Q&A
August 19, 2016
would this blade be ok for 3/4 melamine. if not do any of you have suggestions?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
Bothell
Read all my Q&A
August 24, 2016
Answer: 
Probably not. I use this blade for pressure treated wood, cedar lumber, PVC tubing, and polycarbonate panels. It does an excellent job for those. Melamine panels are typically a hard plastic coating on a particle board substrate. The plastic surface tends to chip badly and randomly when hit with the wrong
blade.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Branchland, West Virginia 25506
Read all my Q&A
Home Improvement Profile: DIYer
August 22, 2016
Answer: 
If the Melamine is a countertop I definitely wouldn't use this blade. I use this blade for framing lumber and ripping.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
6 answers

Would this be ideal for cutting acrylic plastics?

This question is from 7-1/4 in. x 60-Tooth Fine Finish Saw Blade
Asked by
Read all my Q&A
June 5, 2016
Looking to see if this blade can cut acrylic on an beveled angle or cut a small groove into 1/8 inch plastic
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (6)

Asked by
Branchland, West Virginia 25506
Read all my Q&A
Home Improvement Profile: DIYer
August 22, 2016
Answer: 
I don't know
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

June 29, 2016
Answer: 
Hi, ThisGuy - The Diablo D0760R will cut acrylic and plastics. However, if using this blade to cut acrylic, we recommend using a sacrificial piece of wood or tape on the back side of the cut. Also, you should set the correct depth on the saw, the blade should go through the material with no more than 1/8” of the blade showing in the bottom of the cut. This will allow for the most teeth working in the Read More
Hi, ThisGuy - The Diablo D0760R will cut acrylic and plastics. However, if using this blade to cut acrylic, we recommend using a sacrificial piece of wood or tape on the back side of the cut. Also, you should set the correct depth on the saw, the blade should go through the material with no more than 1/8” of the blade showing in the bottom of the cut. This will allow for the most teeth working in the material to get the best cut possible.
We also recommend that you look at blades dedicated to cutting plastics and acrylics, such as the Diablo D0756N and the AvantiPRO P07140R. Read Less
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Tonganoxie KS
Read all my Q&A
June 7, 2016
Answer: 
The answer is, maybe. Feed rate is very important when cutting plastics using a blade meant for cutting wood. Too slow and the plastic will soften and gum up the blade. Best blade is 80 tooth carbide triple-chip design. An 80 tooth alternate top bevel (ATB) blade, either cross cut or plywood style is a good alternative for the occasional user.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Oswego, ILL
Read all my Q&A
Home Improvement Profile: DIYer
June 7, 2016
Answer: 
YOU SHOULD USE A FINE TOOTH BLADE TO DO THAT.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Canton, GA
Read all my Q&A
June 7, 2016
Answer: 
Can't speak for acrylic plastics, unfortunately, but this is one of the best blades I've ever used. I would certainly give it a try on the plastic.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Seattle, WA
Read all my Q&A
June 7, 2016
Answer: 
This blade is really meant for wood, but it will definitely cut acrylic if you push the saw slowly to avoid chipping. The cut will not be as smooth as using a router with high speed rotation and bit meant for acrylic, so you'll have a foggy cut edge if it matters.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
3 answers

Butcher Block

This question is from 7-1/4 in. x 40-Tooth Finish Saw Blade
Asked by
Read all my Q&A
July 8, 2016
How is this blade cutting through 1-1/2" butcher block? Should I go with a 60 tooth instead?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (3)

July 12, 2016
Answer: 
Hi, Mike - You will get the best performance and finish from the D0740R. Given the thickness of the material being cut, the 60 tooth blade will cause minor burning or burnishing on the finished edge. The D0740R will have the correct amount of teeth working in the material to generate the best finish.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
New Hampshire
Read all my Q&A
Home Improvement Profile: Professional
July 11, 2016
Answer: 
Hey Mike!
1 1/2" should be no problem for either of these blades. I was just in the 3402 store this weekend and the 40 tooth was on an end cap for a good price! The extra 5 bucks would get you the 60. It is just a question if you want the finer cut or not.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Hulett, Wy.
Read all my Q&A
Home Improvement Profile: Professional
July 10, 2016
Answer: 
The 40 tooth will cut the Maple 1 1/2" Butcher Block just fine. A 60 tooth would be likely to heat up, and you could have some burnt edges to clean up. Go at a steady feed, but try to allow the blade to clean as you feed it (I always have my depth set up so I can see the bottom of the gullet at the bottom of the cut) HAPPY SAW DUST !!
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
3 answers

Will this blade handle light aluminum cuts?

This question is from 7-1/4 in. x 40-Tooth Finish Saw Blade
Asked by
Read all my Q&A
June 13, 2016
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (3)

Asked by
New Hampshire
Read all my Q&A
Home Improvement Profile: Professional
July 1, 2016
Answer: 
Hey Greg, I was just looking for a saw blade when I saw the 70 tooth D0770F non ferrous metal cutting. I first saw the D0756F 56 tooth non ferrous blade. Good Luck
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

June 29, 2016
Answer: 
Hi, Greg - We do not recommend using the D0740R for cutting light aluminum. The D0740R is not designed to cut non-ferrous materials. The D0756N is designed to cut non-ferrous material including aluminum, brass, and copper.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
New Hampshire
Read all my Q&A
Home Improvement Profile: Professional
June 15, 2016
Answer: 
Hey Greg, The Diablo blade listed for laminate and non ferrous metals is the 56 tooth Diablo Model # D0756N Home Depot numbers: Internet # 202035231 Store SKU # 517197
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
2 3 »
  • 2016-08-27 T16:59:03.033-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_100627136, prod, sort_default
2 3 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 156ms
  • QUESTIONS, PRODUCT

Customer Reviews

Rated 4.8 out of 5 by 367 reviewers.
Rated 5.0 out of 5.0 by Diablo 60 tooth carbide blade I needed a way to efficiently cut corrugated sheet metal. I tried everything without success. Then I found a video on the internet that used a Skilsaw and Diablo blade. Works great but be very careful and wear ear and FULL eye protection. July 26, 2016
Rated 4.0 out of 5.0 by SAW BLADE THE SAW BLADE WAS EXCELLENT FOR TRIMMING THE WOODWORK AROUND MY HOUSE. August 2, 2016
Rated 5.0 out of 5.0 by my go to blade I have been useing these Diablo blades for years. They cut great and stay sharp. These 60 tooth blades make a very smooth cut even on plywood. July 26, 2016
Rated 5.0 out of 5.0 by Perfect Blade For The Job! Had two 3/4", 2x4' popular panels I needed to cut down for an expanded storage area. I didn't have any fine tooth blades for my circular saw. I'm a huge fan of Freud, and have used Diablo blades before. I love their quality of cuts, and this blade is no exception. My cuts were quick, smooth, and clean with no tear outs even when crosscutting this plywood, which was my concern. Diablo blades, and especially this one is an extremely nice blade, well worth the money. High quality product and Highly Recommended. May 25, 2016
Rated 5.0 out of 5.0 by fine cut saw blade nice saw blade and it cuts well . i would buy this anytime i can. June 29, 2016
Rated 5.0 out of 5.0 by Good blades Very good blades for the money, nice smooth cuts, durable. June 28, 2016
Rated 5.0 out of 5.0 by Fantastic Blade After purchasing a Diablo Blade i will never purchase another another brand. There is no reason to go with another brand because the blade will outperform others costing 2 or 3 times as much. May 24, 2016
Rated 5.0 out of 5.0 by Excellent saw blade I purchased the fine tooth blade for cutting 3/4 inch birch plywood with my Skill saw. The blade worked great. This is a 7 1/4 inch blade that I use with my 8 1/4 inch Skill brand skill saw. I purchased the 8 1/4 inch Skill saw from the Home Depot several years ago and I just love the saw. I would highly recommend this saw to anyone. With this saw you can cut more than half way thru a 6 x 6. I think that the Home Depot still sells this saw but I think that it is a special order item. It is hard to find 8 1/4 inch blades unless you special order them or purchase them on line. Of course the 7 1/4 inch blades works just fine. March 22, 2016
  • 2016-08-15 T12:02:52.800-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_367, tr_367
  • loc_en_US, sid_100627136, prod, sort_default
2 3 4 5  ... 13 >>
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 57ms
  • REVIEWS, PRODUCT