Free Shipping and BOPIS

Dundas Jafine

Model # BPCK

Internet # 202449691

ProClean Dryer Lint Removal Kit

This item has been discontinued.
The Home Depot no longer carries this specific product.

$17.79 /each




Model # BPCK

Internet # 202449691

This product will help keep the dryer running both safely and efficiently. Dundas Jafine's ProClean Dryer Lint Removal Kit helps cut the drying time increases the dryer's performance and reduces the risk of dryer vent fire by removing lint build up in all areas of the dryer and dryer duct. This 3-piece kit comes complete with a 10 ft. dryer duct brush, a 36 in. lint trap vent brush, and a vacuum hose attachment.

  • 10 ft. dryer duct brush removes lint and debris that gets built up on the inside of the duct
  • 36 in. lint trap vent brush as well as the vacuum hose attachment helps to deep clean the lint trap of the dryer
  • Vacuum attachment works with any standard vacuum or shop vacuum
  • Works in tight spaces


Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
Brand compatibility 
All Dryers 
Compatible Appliance Type 
Gas Vent Pipe and Fittings Accessory Type 
Dryer Vent 
Hardware Included 
Product Weight (lb.) 
1.7 lb 
Warranty / Certifications
Manufacturer Warranty 
All merchandise is warranted to be free from defects in workmanship and material for one year from date of purchase. Manufacturer will replace or repair at their option. 


Rated 3.4 out of 5 by 41 reviewers.
Rated 4.0 out of 5.0 by Works Well if used Wisely Purchased the brush system to clean out our dryer vent tubing during a remodel. Small brush worked just fine on the dryer. The round brush used for the vent tubing also worked well, removing a surprising amount of lint. However, be warned that if you twist the brush cable as you insert the brush, ONLY turn it clockwise. Turning it counter-clockwise will unscrew the brush and leave it in the vent tubing as I did. (sigh) After considerable effort, I was able to retrieve it, and learned a valuable lesson. So, put some LocTite on the brush threads before using, or only turn the brush clockwise when inserting or removing it from the tube. August 21, 2013
Rated 4.0 out of 5.0 by Be careful As others have noted, the brush head screws onto the cable attachment. The manufacturer recommends rotating the brush in both directions, which is likely to cause the brush to come off in the vent. If this happens 10 feet into the tube, it's a world of trouble. The advice to use loctite on the brush threads is right on. I removed a substantial amount of lint with this tool. It had enough flexibility to get past the bend at the beginning of my duct setup, but not the 2nd bend in the ceiling. You'll likely have to go at the ductwork from the dryer connection and the exhaust port outside. November 1, 2014
Rated 5.0 out of 5.0 by Does what it is supposed to do! I don't know if improvements have been made to the kit, but I did not have any of the issues I have seen in other comments. I wish the brush handle was 15' instead of 10', but I was able to work around the 10' length. I purchased this kit to clean out the dryer vent in my rental house (landlord claimed it was clean, but I was able to pull handfulls of lint where the vent enters the wall). The full run of the vent is 26' with three 90 degree elbows. I only turned the vent brush clockwise on the assumption that turning it counter clockwise might cause the brush head to unscrew. I was able to make it through the elbows by putting a slight bend on the wire just after the brush head, then pushed/pulled the handle while rotating the brush clockwise, this got past all of the elbows. I used the brush from both ends of the vent, pushing the brush in as far as I could shove my arm into the vent (this left a couple of feet of vent that I couldn't reach). I also purchased a 30' piece of 1/8" cable. By attaching a couple of supermarket shopping bags to the cable, I was able to blow the cable through the vent with my shop vac. I then attached the cable to the end of the brush handle and pulled the brush all the way through the 26' vent (and repeated this twice). My shopvac (5 gallon capacity) was about half full of lint when I was finished cleaning the vent. Vacuum attachment was too small to fit on my vacuum so I put a couple of turns of duct tape over the end of the attachment until it would slide snugly into my vacuum tub. I used the attachment to clean my dryer through the lint trap, and to clean out the A/C vents at the registers in my house. I haven't used the "bottle brush" at all, I was able to clean everything I needed to with the vent brush and vacuum attachment. February 2, 2015
Rated 3.0 out of 5.0 by worked fine but brush fell off The brush worked fine, however the brush head fell off quickly and i had to disassemble my dryer vent pipe to retrieve it. I glued the brush back on (not with the cheap glue that it was originally attached with) and it worked fine. If you get this I would recommend that you remove the brush head before you use it, drill out the hole that the arm fits into and re-glue it (I used superglue and that worked well) September 20, 2011
Rated 2.0 out of 5.0 by Product was useful, after some upgrading Duct brush is loosely screwed on. This is a serious flaw, as brush head can come off-inside the duct. Easy to remedy, by gluing on head. Are you listening Manufacturer? Snorkel tool that attaches to vacuum cleaner is folded so tight, as to render it useless, without remedy by opening and holding at full length, heating and reforming, to open fold creases. Duct brush will not go around corners. Brush shaft is too stiff to bent tightly. Plunging brush is very good. This an inexpensive kit, fair quality, limited usefulness July 2, 2013
Rated 1.0 out of 5.0 by Looks like it should work, but mine broke. Just had a short 5ft straight section that I stuck the brush in and pulled it out, Then I wanted to run it back in while twisting, and checked the head attachment, because I'd read the head can come off it you twists the wrong way, and the head did come off. In trying to 'screw' it back on, the fitting came out. If I had tried to use anywhere near the whole length of the tool - with any pipe turns - don't think it would work. March 4, 2014
Rated 3.0 out of 5.0 by Wrx great but has a problem The head is not secured and unscrews as you are winding the brush up the vent to clear it out. After hours of trying different ways to get it out, we had a neighbor who had the right tools to blow it out from the top vent. Yahoo!! We used a thread locker on the head and now it works very well. I am so happy I purchased it. Customer service and shipping was very good. Thanks!!! November 6, 2012
Rated 2.0 out of 5.0 by did not work for me I think this product will work for a long straight dryvent run. Maybe even if it has one 90 degree turn close to access point. My dryer vent run has two 90 degree turns close to access point and as a result I could not get the cable to bend to go around the second turn. I only ordered this product for the 10 foot cable brush and I have don't used the other parts. June 11, 2011
  • 2015-11-29 T11:44:25.210-06:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_41, tr_41
  • loc_en_US, sid_202449691, prod, sort_default
2 3 >>