Rated 4.1 out of 5 by 36
Rated 4.0 out of 5.0 by Doll Used for faux concrete countertops
We used two skim coats of this product to cover our laminate countertops for a faux concrete look. Reading over the directions and coverage information we thought we would only need 4 boxes total. We ended up needing 7.5 boxes. We used the directions to mix entire bags at once, but each batch came out with a different consistency so we had to start mixing 1/4 bags at a time. The final look came out like we imagined minus the one area with a bad consistency.
July 19, 2016
Rated 4.0 out of 5.0 by MM Used for concrete counter tops
We used this product to "overcoat" the concrete counter tops we built. I used a 3/4" piece of plywood, covered with aluminum grating screwed to it. Pre-drilled holes for sink and faucet and plugged them. Installed trim on the front to hold in the concrete. Poured concrete and let it dry. At that point we used the Featherfinish to fill in the remaining area to make it level with the top of the front trim sanding as needed in between. After 30 days, stained and sealed it. Looks great! The only advice I will give for the featherfinish is that it is easier to use in thinner layers. We did 3 counters and the thinner you do it the easier it is to work with. You can do it thick and you can stain and seal it.
April 19, 2016
Rated 4.0 out of 5.0 by Tadco Floor prep
Works well, easy to apply, only issue is drying time longer than stated
August 23, 2016
Rated 5.0 out of 5.0 by beautifulbusdriver this stuff is great...
i am a 60 year old DYI person. it would have been too expensive to tile my downstairs (slab). I decided to create the wood floors I wanted that would stand up to my husband in regard to the cleaning issue.
I removed all carpet and any fake tile. cleaned my floors well and let dry. I mixed henry's to a slightly thicker consistency than pancake batter. I poured on the floors. let it set for ONLY A FEW MINUTES, scored my planks and ran a wood graining tool along the planks. after I did the entire room I let it dry. I sanded the floor lightly and as necessary to smooth out. vacuumed well. I wanted dark floors so I watered down some rustoleum black paint. used a roller to apply. let dry. for a weathered look I sanded areas to remove the paint. sealed with cement sealer. I get so many comments about my wood floors. I can scrub my floors with a brush and they still look great.
April 30, 2016
Rated 5.0 out of 5.0 by 2eagles Best patch / skim coat I've worked with...
...had 3/4 of the box left after filling holes/ leveling so I applied it to my hideous 70s yellowed fake marble bath counter! It was super easy - if you can frost a cake you can cover a counter. Took maybe 3 hours total application, smoothing then a light sanding, for a 4' counter. It's curing now, heading to HD for sealer.
March 30, 2016
Rated 5.0 out of 5.0 by Reese Does what it says.
Good product. Easy to use as long as you know how long you have to work with it.
May 3, 2016
Rated 4.0 out of 5.0 by indigoskyy great decision
had to apply quite a few more coats than anticipated but i am happy with the end result. even with having to purchase more product than i was planning, it was much cheaper than purchasing all new countertops right now and it gives it a cool industrial look. backsplash is being redone now! :)
April 29, 2015
Rated 1.0 out of 5.0 by skiddie95 Seized up solid in under 5 minutes
I bought this to apply to a small laundry room floor. Got only one trowel's worth out of it. You either have to keep stirring to keep it soft or you have to accept that it will seize solid within 5 minutes of your stopping. I followed the directions to the letter -- and watch my money solidify in the bucket.
March 21, 2016