Flotec 1/2 HP Submersible 2-Wire Well Pump-FP2212 - The Home Depot


Model # FP2212

Internet # 100144017

Store SKU # 724854

1/2 HP Submersible 2-Wire Well Pump

Flotec 1/2 HP Submersible 2-Wire Well Pump

This item has been discontinued.
The Home Depot no longer carries this specific product.

$326.00 / each
  • Lifts water up to 150 ft.
  • Floating stack offers sand resistance
  • Includes a built-in check valve


Model # FP2212

Internet # 100144017

Store SKU # 724854

Store SO SKU # 1000291312

The Flotec 1/2 HP Submersible 2-Wire Well Pump features energy-efficient operation and is designed for use in wells with inside diameters of at least 4 in. and depths of up to 150 ft. The floating-stack design minimizes sand locking while the stainless-steel pump and motor housing resists corrosion.

  • Pumps up to 10 gal. per minute
  • 2-wire design for energy efficiency
  • Stainless steel housing, heavy-duty discharge connection and precision-molded impellers and diffusers provide durability
  • Installs in wells with 4 in. diameters and larger
  • Water filled submersible motor

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.


Assembled Depth (in.)  33.938 in  Assembled Height (in.)  4.063 in 
Assembled Width (in.)  4.219 in  Maximum Pumping Depth (ft.)  150.0 
Product Depth (in.)  33.938  Product Height (in.)  4.063 
Control Box Included  Yes  Head Pressure (ft.)  40.0 
Horsepower (hp)  1/2 hp  Housing Material  Stainless steel 
Inlet Connection  Barb/rib  Maximum Discharge Flow (gallons/hour)  816.0 
Maximum Discharge Pressure (psi)  50.0  Outlet Connection  Threaded female 
Product Weight (lb.)  21 lb  Returnable  90-Day 
Run-Dry Capable  No  Self-Priming  Yes 
Wiring Configuration  2-Wire 
Warranty / Certifications
Certifications and Listings  CSA Listed  Manufacturer Warranty  3 Years 


Rated 3.4 out of 5 by 9 reviewers.
Rated 5 out of 5 by this was great at a low cost this pump installed very easy.great product for the cost.the ability to use my bill me later was great. July 31, 2012
Rated 1 out of 5 by Too weak, hasn't worked right. I installed two of these. The first one died after about a year and a half. The newest one has been not working for about two years. It kind of works, but is too weak to be adequate. If it's powered off, for about two hours it comes on and off, and then finally works 'normally'. It's not the pressure switch, or the pressure tank, both were changed, with no change in behavior. Also, it's a weakling. It can't get the pressure past 40 PSI, so I had to downgrade my pressure switch to work with this dud. The well is about 150 feet, maybe this item would work better with one more shallow, at least as far as maintaining pressure, but overall, it's a lousy item. Get something better, you'll be happier in the long run. July 31, 2013
Rated 5 out of 5 by Flotec 1/2 hp submersible pump no control box needed This is the 4th Flotec stainless submersible we've bought. Two were 3/4 hp. But we're very pleased with all so far. One has been in use for many years and still supplies water to 3 homes. Our first 1/2 hp pump replaced the deep well jet pump that supplied our home. The submersible is vastly better...quiet, powerful and seems to use less electricity. Wiring is so much easier with the 2 wire system! The two 'hot' wires go to the 'switched' terminals on the pressure switch...two 'hot' wires from the 240 volt service go to the 'hot' terminals of the pressure switch, and the green goes to ground. No 'control box' to go bad [as they sometimes do]. I like the fact that the pump is stainless and plastic...nothing to corrode. Suggestion: use at least 2 torque arrestors several feet apart and/or plastic spacers to keep pipe and wires centered in the well. Otherwise, starting torque CAN rub the wires or pipe against the side of the well. My father-in-law had his submersible pump [brand unknown] stop working because the wires were completely severed. May 23, 2013
Rated 5 out of 5 by this was easy to install this product was easy to install , you had the pump , you had the barb fitting . I needed a check valve you didn't have I needed a brass nipple you didn't have . If your going to sell the pump you need to carry the fitting to be able to install it September 20, 2012
Rated 1 out of 5 by Im so angry right now I drove 3 hours round trip in a blizzard, bought this pump, I read on the box and it said 1 1/4" discharge which is what my old pump was. I get all the way home, open the box and its 1 1/2" discharge... February 13, 2014
2 >>


Standard Shipping includes delivery by small parcel service. Processing time varies by product.

If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.