Rated 4.3 out of 5 by 4
Rated 3.0 out of 5.0 by GaryWasher Disappionting
Price is everything here. We can't expect this wrench to be as good as a quality new one priced at twice the cost. So here are my findings with this one:
First, let's be honest, this is NOT a 36" pipe wrench. If it were the standard 36" size, it could be used on 5" pipe, and that is not the case. It measures just under 30" and that would be in line with a wrench that can be used on 3 1/2" pipe (this ones max). The specs show the max pipe size as 5" but that is not possible. While it is true that the jaws can be opened to ALMOST 5", that would make for about a 4" ID pipe. The 5" stated in the spec should have been either 3 1/2" or 4". 3 1/2" is the maximum size shown on the pipe size guide molded into the movable jaw. Since the 36" number is also molded into the handle and the adjustable jaw, this makes for a difficult time judging the wrench size. Two things would have fixed this: State the wrench size as 30" and state the max pipe size as 3 1/2". With those fixes this would not be an issue.
Second, This wrench works acceptably for occasional work, but I would not recommend it for everyday use. This is mainly because the adjuster is very cumbersome and usually requires the use of both hands to operate, one to turn the nut and another to move the adjustable jaw. Adding simple thrust bearings or washers on each side of the nut would help a lot. This might be added later by the user, if he/she can find washers to fit the 1 1/2" diameter adjuster screw.
Third, I like the low weight of the aluminum handle. If this wrench were to used a lot, it would save a lot of work by itself.
Fourth, The jaw serrations seem fairly sharp and well machined. Only time would tell if they are dulled quickly over time or remained effective.
Fifth, These jaw teeth/serrated plates are not really replaceable. The ones in the adjustable part are integral to the part. You would have to replace the whole jaw to replace the teeth. The other set of teeth are separate from the handle and are fixed by a single roll pin. While that theoretically could be replaced, I doubt that a replacement part is available.
Sixth, The tensioner/spring parts are easily removed, unlike some wrenches. This makes them easy to examine and re-oil or re-grease. Generally there are only 5 parts to this wrench, the handle with fixed jaw, the adjustable jaw, the fixed jaw teeth (fastened to the handle), the tensioner coil spring, and the tensioner plate.
Last, even though this was a difficult decision, I cannot recommend this wrench because of the problems stated above. Use the same money to buy a quality used wrench. On the other hand if you can use a 30" wrench and can add the thrust washers for the nut, this may work for you.
March 10, 2014
Rated 5.0 out of 5.0 by Autobroker Great pipe wrench
This is a great heavy duty pipe wrench. The finish is a nice painted silver color. The aluminum saves a lot of weight and even though it's 3 feet long, it weighs about the same as an 18" steel pipe wrench. The jaws are steel and are replaceable. The teeth on the jaws are well machined and strong. This is a great wrench for heavy duty plumbing work. This wrench feels very heavy duty and I feel it will last a lifetime. It would not be a good choice for under the sink plumbing, due to the large size.
After using this pipe wrench, I understand the weight benefit of using aluminum. I also no longer worry about the durability of aluminum. This has impressed me so much that I will be changing out my entire pipe wrench set to aluminum. I highly recommend Olympia for a quality aluminum pipe wrench.
February 28, 2014
Rated 4.0 out of 5.0 by AchersAway Works as it should
This wrench is just like the Rigid, but made in China. I'm disappointed the Home Depot does not specify if their products are imports or not. This is a Rigid Knock-off, yes it works for use around the house. If you use this tool every day for hard work them buy a Rigid.
March 12, 2014
Rated 5.0 out of 5.0 by Sudshunter Awesome pipe wrench !
I bought this pipe wrench for 3"-4" pipe, no problems with the 3" but it just don't do the 4" at all. I'm not complaining,because I wasn't sure if it would open enough for 4" or not, besides that give me a better reason to go ahead and get that 48" aluminum pipe wrench I want !
February 27, 2014