Rated 3.3 out of 5 by 12
Rated 2.0 out of 5.0 by GirlZero This snozzle is just too thin as far as the plastic used to make it. If you buy the largest size of the 7200 glue this applicator just dies. I have gone through 2 so far, 1 per bottle of glue that I have needed to use. I will need at least 2 more to finish my project. By the end of the tube there is glue coming out of the sides and seams of the applicator. It is messy. All and all I would recommend it, because the directions on the glue call for it and I like to follow directions.
October 26, 2016
Rated 5.0 out of 5.0 by steve Works great
Its a disposable nozzle. If you are running a bunch of cove base its great, applies the adhesive evenly..No trowels or multiple beads. Cuts install time. Its worth the 3 bucks if you are running more than a few pieces. Ive used these numerous times never had one split? Maybe if you were using some heavy bodied adhesive or caulk but Ive never had problems. User error? Ive seen guys blow out caulk tubes or get reverse flow at plumger end with too much pressure for the opening in the tube. Technique matters in everything...
September 15, 2016
Rated 1.0 out of 5.0 by BrOK Convenient, but quality is junk
Pro: Its cheap & it will allow you to apply adhesive quickly.
Cons: Its extremely poor quality. The plastic is thin and poorly seamed together
I bought 2 of these for a 2 day job. Once I started clicking the caulk gun to fill the snozzle under pressure the seams split and the caulk came out the side. I had this happen on both of them. I pulled the nozzle back off, wiped off the caulk and tightly wrapped it in electrical tape and was able to continue.
September 12, 2016
Rated 5.0 out of 5.0 by Dreisdale Excellent!!!
Saved time AND glue (decreased excess glue oozing out of top and bottom of molding); you will love this tool IF you treat it as what it is intended to be -- DISPOSABLE accessory to make your job easier!
June 17, 2016
Rated 1.0 out of 5.0 by Hans Totaly unecessary
It looks like a good idea, this is what is going to happen, it will work at your first use and while you spread it, you will think to your self what am I doing?, so much waist of glue inside this thing, I could easily have done exactly the same thing without it and after the first use it will get clogged and you will have to through it away...., really.. save your valuable money and the embarrassment to your self.
March 26, 2016
Rated 5.0 out of 5.0 by Steve Great tool, highly recommended
I replaced a kitchen floor that had cove base molding rather than standard baseboard molding. The cove base was in great shape so I decided to try to reuse it. It came off the wall easily and required very little scrapping to clean it up. The only negative reviews I read about this adhesive spreader was that the adhesive dried in the spreader and clogged it so I knew I had to keep moving until the job was finished. With all the cove base laid out in its proper location I began. The spreader worked beautifully. It applied neat, even rows and the thickness of the beads was adjustable by altering the angle of the spreader. I used a small paint roller to adhere the base to the wall evenly. Once used the spreader is impossible to clean so plan on trashing it, it's only three bucks. I couldn't be happier with the results, the spreader worked perfectly. I highly recommend this tool for any cove base installation.
December 9, 2015
Rated 5.0 out of 5.0 by Nick Must have for baseboards!
I don't know how I installed vinyl baseboard without one of these, I'll buy one everytime I order baseboard in the future. I only ordered this because I was installing 6" vinyl base and thought it might be a pain to deal with on a 120' roll. It was so much easier than try to apply and spread the old way. I would treat this asa disposable per job (or per day) but it is definitely worth it.
November 10, 2015
Rated 4.0 out of 5.0 by CoachB Well worth it
Perfect size for molding, wasted a lot of glue inside when done but speed and ease of use more than made up for it!
December 8, 2015