Questions and Answers for Glacier Bay Slat Style 24 in. W x 9.5 in. D x 64.5 in. H Satin Nickel Over-the-Toilet Storage

A:  We're sorry to hear that you lost some of your hardware, Sheran. If you need replacements, our customer service agents are happy to help. You can reach them Monday through Friday between 8:30am and 5pm Eastern Standard Time. To contact them, dial 1-800-892-3986 or send an e-mail to customerservice@mayzon.com.

A:  Hi Jrin, the total width of this Over-the-Toilet Storage is 24 inches. The inside width would be slightly smaller. For additional product information, please contact our Customer Service Department Monday - Friday from 8:30AM to 5:00PM EST at 800-892-3986. Thank you!

A:  Hi Mike, for this Glacier Bay Slat Style Storage, the leg themselves are 9.5 inches in width, 0.5 inches thick. For additional product information, please contact our Customer Service Department Monday - Friday from 8:30 AM to 5:00 PM EST at 1-800-892-3986. Thank you!

A:  Hi Randi, thank you for your inquiry. The lower support bar can be placed at 5.902" or 7.402". For additional product information, please contact our Customer Service Department at 1-800-892-3986. Thank You!

A:  Hi, the width of this product is 9.5 in. Thank you!

A:  The one I received is brushed nickel

A:  It is brushed, not shiny.

A:  Hi, this item is a brushed, satin nickel. Hope this helps!

A:  Yes, absolutely no issue.

A:  Hi LinMarie, thanks for asking about the Glacier Bay Slat Style Over-the-Toilet Storage! The slats on each shelf come attached (you do not have to assemble each individual slat), so they do lay evenly. If you'd like to take a look at the Installation Guide to learn more about the parts and assembly process, it's linked under "Info & Guides" about a third of the way down the Home Depot website page. We hope this helps, thanks!

A:  I couldn’t anchor mine to the wall, because said wall is tile and mirror, so I used damage-free 3M Command Strips to secure it.

A:  Anchors and screws are supplied. I needed some longer screws, and a couple of spacers between the shelves and the wall since my baseboards keep the unit about a half inch from the wall. You could use other anchors if you prefer. Screwing it to the wall was a little tricky because of the position of the holes; you need a short handle #2 philips. A compact or angled drill motor would be great. Once anchored, the unit is very solid, it doesn't budge.

A:  Hi KT, thanks for asking about the Glacier Bay Slat Style Space Saver! To mount this unit, first make sure the assembly is level. If not, adjust the feet (Part DD in Instruction Guide) as needed. Next, mark the mounting points on your wall through the holes in the rear tubes of the unit. Hammer the wall anchors (Part FF) into the wall, unless the mounting screws (Part EE) will go directly into a stud (if this is the case, no wall anchors are needed). Place the unit against the wall, lining up the wall anchors (Part FF) and holes in the rear tubes. Finally, tighten the mounting screws (Part EE) into studs or wall anchors (Part FF). To learn more about assembly and installation, please feel free to take a look at the space saver's Instruction Guide which is linked about a third of the way down the product's Home Depot website page under the "Info & Guides" section. If you have any additional questions or concerns, please reach out to the manufacturer's U.S.-based Customer Service department by calling 800-892-3986. We hope this helps, thanks!

A:  My wall has paneling backed by plywood so I just use a couple of short wood screws. The kit comes with 2 drywall anchors and 2 screws . The back legs have a whole under the middle shelf both sides.

A:  There are holes in the middle top portion of the frame that butts up against the wall to either use screw, if in a stud, or molly screws if not that secure it and anchor it to the wall. Also, the bottom back bar goes behind the commode so it also secures it,