Questions and Answers for Hampton Bay Andenne 26.3 in. 3-Light Transitional Bronze Bathroom Vanity Light Fixture with Marbleized Glass Shades

A:  I hired a painter and he removed it to a point where he painted around and placed it back where it was. Maybe call someone from Home Depot can help....

A:  If you had to have it installed probably the easiest way would be to get some masking tape and just wrap around the base of that thing to do your painting. I'm not specifically familiar with this light fixture but normally fixtures of this type are attached to the wall with a couple of small screws that have metal balls on the end so when you look at the at the fixture it looks like small spheres maybe about a quarter of an inch on either side of the light right at the base. Those spheres are attached to threaded screw that hold the light fixture to the wall. You would just unscrew them while holding the light fixture. Remember righty tighty lefty Loosey. The fixture will come out it'll still be wired into the wall so you'll have the white and the black wires connected and there's probably a copper grounding wire connected as well. The light should be wired well enough to hang from the wires so you can paint the area under the fixture. We don't wait for the paint to dry before resetting the fixture if we are pressed for time. Good luck.

A:  There are big nuts that screw onto the light recepticles inside each globe. These nuts are what holds the globes onto the fixture. You had to remove them to get the globes off the fixture.

A:  Adjust the Mounting bracket on Step #1 --> pre-installed screws should be at Vertical position. Shims required to make bracket flush with wall. https://www.homedepot.com/catalog/pdfImages/45/45d4dc1a-edfa-47aa-9b00-4124450cc074.pdf

A:  When you say "globe" I assume you mean the glass lampshade. Remove lamp (light bulb)..You need to tighten the threaded ceramic lock ring snug up to the neck of the glass. Be very careful not to overtighten, or it will break. Sometimes you need to wiggle or rotate the glass while tightening the ceramic ring, being careful, these things break easily .

A:  Installed in under an hour. Did not encounter any problems.

A:  If you have to ask this question call an electrician or handyman.

A:  This is 26.3" wide.

A:  Roughly 27 inches (measured over the 3 shades)

A:  Good question. I wish I had the answer. The website for Hampton Bay is www.hamptonbay.com or 1-855-HD-HAMPTON

A:  I don't know for sure, but they have many types of individually purchased shades in the store.

A:  I'm thinking you could get them from a ceiling fan store or something like it.

A:  Hi BJ please get in contact with us by calling 1-800-446-9092 and ask for the parts department.

A:  Look at manufacturers website or call them for a catalog.

A:  Their are many in store or online.

A:  I had to do the same thing. I put andenne light in the search box of the Home Depot sight and came up with similiar choices.

A:  Home Depot sells shades in the store.

A:  Hi Corey, please contact our parts department at 1-800-446-9092.

A:  This is 26.3" wide.

A:  Hello Kitkat, this fixture is 26.3 inches wide.

A:  Any good quality incandescent bult should work as long as you have a dimmer switch on the wall. I use these round ones and they look great. You could also use an LED bulb but be sure to check to make sure they are dimmable.

A:  Look for dimmable bulbs that go down to 10 percent.

A:  The oval shaped mounting plate is 5 inches tall, 7 inches wide.

A:  Hi Sandi, the mounting plate is 4.5 inches tall by 7 inches wide.

A:  If you have a Line (Hot) wire to both.

A:  Check with your electrician. I wouldn't do it just for safety reasons.