Questions and Answers for Lutron Diva 3-Speed Fan Control and Light Switch, Single-Pole/3-Way, 1.5A Fan/1A LED, Black (DVFSQ-LF-BL)

A:  No - Not easy to install

A:  If the wires were initially run with no intention of installing a ceiling fan, you may not have enough wires for this control to work. This control would require 2 separate switch legs (one of the fan and one for the light) as well as a hot wire to feed power to the control.

A:  Hi CluelessHomeowner, Hard to tell without seeing what is there, but all homes I wired had both a two switches in all bedrooms going from ceiling to switches so had one switch for light and one for fan so the Diva would work but would leave one switch location blank but that is ok. To see what you have would need to open switch location and you would need to see if you have wire colors black, white, red and green or bare wire, if you have that then this will work. If not you would been to replace wire from ceiling box to switch

A:  The DVFSQ-LF will only switch the light on/off and control the fan speed. If you would like to dim the light and control the fan speed, Lutron would suggest the MACL-LFQ-WH.

A:  No, this product does not work as a dimmer.

A:  no , only controls the fan speed

A:  Hi SaulTrain, It sounds as if you have this switch wired incorrectly. The paddle portion of this combination switches is simply on/off. The slider is a separate switch and controls fan speed. 120vac gets connected to the black wire. The red wire goes to the fan motor and is for VARIABLE speed. The yellow wire goes to light and is CONSTANT voltage.

A:  We are sorry to hear about the issues you are having. The DVCL-153P is only rated to control 150W of dimmable LED/CFL or 600W of incandescent/halogen. This product has a minimum load of 40W incandescent/halogen or one compatible LED/CFL. Please reach out to our 24/7 Support Team at support@Lutron.com or by phone at 1 (844) 588-7661 with any questions/concerns.

A:  Disregard question. Problem was my box fan. Switch works great. Highly recommend this product!

A:  What do you mean by "tie paddle switch with a plug"? Why are you using a plug somewhere in this circuit? Need more info to answer question. In general, a voltage fluctuation might indicate a loose connection.

A:  This Fan Control and Light Switch is available in Black. The model # for this color finish is DVFSQ-LF-BL.

A:  Yes, see the dropdown box for a wide variety of colors including black.

A:  it comes in many colors including the black to

A:  This Fan Control and Light Switch is available in Ivory. The model # for this color finish is DVFSQ-LF-IV.

A:  There is a dropdown box on the product page that lets you select from quite a few colors.

A:  Hi Marie, this Diva Fan Control and Light Switch for LEDs, CFLs, Incandescent and Halogen, does not come in Ivory. We do offer other options on Homedepot.com that may suit your needs. Please review the products at the link I have provided below to see if any will work for your project. http://www.homedepot.com/s/Diva%2520Fan%2520Control%2520and%2520Light%2520Switch%2520for%2520LEDs%252C%2520CFLs%252C%2520Incandescent%2520and%2520Halogen%252Cbeige?NCNI-5 We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot!

A:  when you get to the page you will have ability to open the drop box and choose the color do that before you add to the cart

A:  This Fan Control and Light Switch is available in Ivory. The model # for this color finish is DVFSQ-LF-IV.

A:  Yes, see the dropdown box on the product page to select from a wide variety of colors including ivory.

A:  it comes in many colors including the ivory to

A:  Bob, This switch will work as long as the necessary hard wires are in place for separate fan and light control. There must be separate hot wires run for each. For example, typically a 14-3 wire having a white, black and red conductor would have been run to the fan when the original wiring was done. The white is neutral. The black wire would control the fan and the red wire would control the light. If you do not have these wires this switch will not work.

A:  as long as you have 4 wires going to your fan and the switch will not get water it will work

A:  Hi Bob T, From what you said not will not work as you need existing one switch for fan and one for light. So in the switch box to the light need a 4 wire w/ground, assume is romex so would be 12 or 14/3 romex cable

A:  This product is only rated to control a single fan and is not recommended to be used in an application with two or more fans wired to a single switch.

A:  Normally, when a fan already has a receiver installed, the receiver will block 3rd party controls. Due to this fact, Lutron would recommend contacting Hunter to see if this is the case for your specific fan.

A:  it will work as long you have 4 wires going to your fan and you remove the transmitter from the fan. which means you will no longer use the wireless control

A:  Probably not without running a separate power wire from the switch location to the the fan.

A:  Yes, the slide can turn the fan on and off.

A:  It turns the fan on and off as well as controlling the fan speeds

A:  The fan control portion on this product can turn the fan on/off as well as adjust the speed.

A:  If the two wires running to your ceiling outlet are separate switched legs for the fan motor and the light kit this control will work. However if you only have two wires in the wall box location where the fan control is being installed and one of them is providing the line voltage, this control would not work.

A:  Hi Rod no need 3 wires, power, an return wires for fan and light. Current codes require neutral in box, then you also should have a ground wire