Questions and Answers for Southwire 25 ft. 12/2 Gray Solid CU UF-B W/G Wire

A:  It'll work for up to 25 amps for 25ft. Up to 10 amps on a 50ft run. This is for a 10% voltage drop.

A:  In my limited experience, so long as the GCI outlet placed is wired correctly and you aren't tying this outlet into another GCI it should work the 12/2 w/Ground is used in 3-wire systems and should not have any negative impact.

A:  Yes it can . Remember the box should be weather proof and outlet cover too.

A:  Most definitely it's out door use and ground burial.. I have several light fixtures and GFCI outlet. A little hard to bend but it will,

A:  It has outside diameter of 463 x 183 mil.

A:  Probably, if the local code allows. i would not staple or nail through in order to avoid breaking thew moisture seal.

A:  I used 3/4 conduit, and it wasn't really a tight fit, but I wouldn't use anything smaller. But that's me, you might be fine with 1/2 in.

A:  Like you, I prefer to run my electric underground cable in outdoor schedule 40 PVC conduit. Whether or not you could fit this wire in 1/2 inch conduit, I strongly recommend you using 3/4 inch conduit. It will be much easier to snake the cable and the electrical wires might not heat up as much, with more air circulation .

A:  Check with your local building codes but as a matter overall I would definitely put it in conduit and I do believe that most building codes are consistent with that requirement

A:  Although this is made for ground contact, so it can withstand a lot, you should use a conduit on an exposed wall. The elements are harsh and you don't want to take unnecessary chances. It'll look better, more professional that way.

A:  Yes, it's over kill but yes. Southwire's copper UF-B cable is used in applications that include outside lamp posts, pumps and other loads. It can also be used for outbuildings such as garages and barns. UF-B feeds from a distribution point in an existing building. UF-B has a heat capacity of 90°C and is rated at 600-Volt.

A:  Its sort of like exterior paint, you can use it inside as well but you can't use interior paint outside. The wire would be fine to use inside, its overkill but there is not an issue code or safety wise.

A:  Yes this will work fine indoors. You must follow code but this will work just fine indoors.

A:  Yes, you can use it inf\door. It's just heavier duty for outdoor.

A:  We would love to answer your question but are not sure what you are asking. Can you please clarify your question?

A:  Yes dis can de bearied in the ground

A:  I would not. 240 circuit should use 12-3 up to 20 amps.Better still use 10-3 it will handle the load better.

A:  No, you will need 12/3 w-Ground for direct burial - This wire is rated for 20 amps - about 2000 watts @ 120 1ph. The 12/3 will handle about 4500 watts @ 240 1ph. If the heater is larger than that you will need a larger size wire. Typically I size wire at 75% load for safety, & future expansion.

A:  It depends on the amp draw and how long of a run you’re doing. If it’s less than 20a and less than 50 feet this will be good. More than that 10/2 would be a better choice.

A:  As long as you don't need a neutral, it is.

A:  I would NOT use this, Scott. This is more expensive because it can be buried in the ground (as I did). You could use (less costly) https://www.homedepot.com/p/Southwire-25-ft-12-2-Solid-Romex-SIMpull-CU-NM-B-W-G-Wire-28828221/202316378 BUT If you foresee ever wanting to have 120V available, I suggest 3 wire with ground, such as https://www.homedepot.com/p/Southwire-25-ft-12-3-Solid-Romex-SIMpull-CU-NM-B-W-G-Wire-63947621/202316448 |<----------220--------->| |<-- 120 -->|<-- 120 --| |<-Hot         |                 |<Hot     |<-Netural and safety Ground

A:  Please consult a local electrician. The above advice is based upon the current edition of the National Electric Code (NEC). Free access to the latest version of the NEC is available online at www.nfpa.org/freeaccess. The NEC and local building codes regulate the types of wire and cable that can be used in specific electrical applications, as well as the manner of installation. Check your local building codes before you start any wiring and cable electrical project and be sure to obtain required permits. When your work is complete, always have it inspected for compliance with local codes to ensure that it has been safely installed.