Questions and Answers for Zenna Home NeverRust 50 in. to 72 in. Aluminum Tension Curved Shower Rod in Bronze

A:  Hi, Confused, we are very sorry you’re experiencing trouble assembling your curved shower rod. We recommend two people for installation. Step 1, shorten the 7/8” diameter tube assembly as much as possible by twisting opposite the direction indicated on the twist until fully tight sticker. Step 2, align the mounting bracket and attach it the 7/8” diameter tube using the mounting bracket screw and threaded insert. Step 3, align the mounting bracket and attach it to the 1” tube using the mounting bracket screw and threaded insert. Step 4, slide one end cap on the 7/8” assembly then align the dimples on the end of the end cap and snap them together. Follow the same instructions on the end of the 1” diameter tube. Step 5, align the flat side of the flat side of the plastic ring to the flat area in the 1” diameter tube and insert it. Step 6, slide the 7/8” tube into the 1" diameter tube. Step 7, measure the space where your rod assembly will be installed. Step 8, extend the rod to that measurement. Step 9, lock the link of the rod assembly using the rod set screw tightening it flush to the rod assembly. Step 10, position the rod assembly between the walls curving away from the tub with the rod set screw facing down. Secure the rod by twisting the end of the 7/8” rod tube in the direction on the twist tightening it until it’s fully snug. Make sure the rod is level and adjust as needed. Step 11, fully tighten the rod assembly by twisting the end of the 7/8” tube assembly. If you need additional assistance, please contact our customer service experts at 1-800-892-3986. They are available Monday through Friday, from 8:30 am to 5pm EST. Thank you

A:  Hi IYSR, if your shower opening is between 50inches & 72inches, it will not be necessary to cut it. Once you assemble the rod, adjust it to the length you need, then lock it by inserting the rod set screw. Please feel free to reach out to the Customer Service department Monday - Friday from 8:30 AM to 5:00 PM EST by calling 800-892-3986. Representatives are available to assist you with step-by-step installation instructions. Thank you!

A:  You can extend or reduce the length of the rod. Then tightened with set screws. 

A:  Hi Pradeep, $39.63 converted to Indian Rupees is 2959.02547 INR. Thank you!

A:  Hi Trixie, thank you for your inquiry. This end cap measures 4 1/8"D. Your Rod if extended to 72" will allow an additional 6" of elbow room. For additional product information, please contact our Customer Service Department at 1-800-892-3986.

A:  End caps are 4.5 inches in diameter. The rod bows about 4 inches or so. Hope that helps!

A:  The footprint of the end caps is 4" and the rod bows out approx 4-5".

A:  Thank you for your inquiry. This is a tension rod and is designed to detach with unlocking your rod in the center by twisting inner and outer tubes in the opposite direction. Your end caps do not have screws or stickers. For additional assistance, please contact our Customer Service Department at 1-800-892-3986.

A:  I think you just grip it and twist it counter clockwise mine came off wall ok.

A:  The product is great, but they way I was handed by the customer service was not the best!

A:  The end cap diameter in 4 inches

A:  The part of the cap that sits against the wall measures approximately 4 1/8".

A:  Thank you for your inquiry. The diameter for the end caps on this model measure 4 1/8". For further information regarding this product, please contact us at 1-800-892-3986.

A:  Yes, just like the standard straight one except is curved. No drilling needed.

A:  Thank you for your interest in our product. Yes, this Shower Rod is held up by tension requiring no holes. The curve in the Rod will add an additional 6" of elbow room to your shower space in comparison to a straight shower rod. For additional information about this product, please contact us at 1-800-892-3986. Thanks again!

A:  You twist and place, although it's a little trickier because of the curve. No drilling. I haven't measured the curve but I think it's pretty good.

A:  yes it is a tension rod...no drilling required. the curve extends the curtain out about 6 1/2 inches

A:  Thank you for your interest in this product! This Rod is Rich brown in color. For additional questions regarding this product, please contact the manufacturer's toll-free Customer Service Department at 800-892-3986.

A:  Yes it is.

A:  Yes it is a dark bronze possibly oil rubbed or a chocolate brown color.

A:  Yes it is a dark bronze. It matches the Delta faucets in our bath.

A:  it's dark bronze