A: Our total length on the drawer pull is 5 1/4 inches. The measurement from hole to hole is 3 1/2 inches.
by|Jun 22, 2023
Q:How do I measure kitchen cabinet handles
by|Apr 14, 2023
1 Answer
Answer This Question
A: Jules, thank you for your question. The best way to measure the cabinet handles would be center to center. We do have a template that may be used for measuring the holes. ~Best, Liberty Hardware Customer Care Team
by|Apr 19, 2023
Q:What is the width of the opening for your hand to pull the handle (not "center to center of mounting holes"). In other words, how wide is the pull at the 1 inch height level?
by|Jan 22, 2023
2 Answers
Answer This Question
A: normal female adult hand. see photo
by|Feb 1, 2023
1 found this answer helpful
A: space between drawer front and front of pull is about 3/4 inch. Wide enough to get 3 fingers in the space. But the pull is not flat, but rounded, so the space decreases as you go from center to edge where the screws are. Hopes this helps.
by|Feb 1, 2023
1 found this answer helpful
Q:Do these come with 2 different lengths of screws ? shorter for cabinet doors and longer ones for drawers?
by|Oct 4, 2022
1 Answer
Answer This Question
A: Just the two screws needed to screw it directly into the wood. This isn't installed as a bolt all the way through that you thread into the pull.
by|Nov 24, 2023
Q:Can these be used on a fireplace grate cover? Will they stand up to the heat or would they warp/melt?
by|Feb 28, 2021
2 Answers
Answer This Question
A: Hmm... They are metal so they will not melt in that application but... Not sure if the paint will hold up to the heat... Good luck.
by|Nov 16, 2022
1 found this answer helpful
A: Samantha, Thank you for your question on the Liberty Hammercraft 3-1/2 in. (89mm) Center-to-Center Black Front Mount Drawer Pull. The pulls are not intended and have not been tested for use under extreme heat. Therefore, we cannot recommend this application and will void the warranty. Best, Customer Care Team
by|Nov 16, 2022
1 found this answer helpful
Q:My aunt has these on her kitchen cabinets and wanted to replace with something more minimal. I removed one, and much to our dismay, there was an imprint of the spade shape in the finish.
What type of pull could be used to cover such a large, odd-shaped imprint? Sanding/painting is not an option.
Thanks!
by|Jan 30, 2021
2 Answers
Answer This Question
A: Xsie, thank you for your question on the Liberty Hammercraft 3-1/2 in. (89mm) Center-to-Center Black Front Mount Drawer Pull. To better assist you with another pull, please reach out to your local The Home Depot sales associate for guidance. Best, Customer Care Team
by|Feb 1, 2023
1 found this answer helpful
A: If you don’t want to fill, sand and paint then how about spray painting them a different color. These are vintage type pulls and I love them.
by|Feb 1, 2023
1 found this answer helpful
Q:Does this come with the screws?
by|Dec 24, 2020
4 Answers
Answer This Question
A: yes
by|Mar 4, 2023
2 found this answer helpful
A: Yes, the screws come with the handles, and they match in color.
by|Mar 4, 2023
2 found this answer helpful
A: Lisa, Thank you for your question. The Liberty Hammercraft 3-1/2 in. (89mm) Center-to-Center Black Front Mount Drawer Pulls come with (2) 8-32 x 1" screws. Best, Customer Care Team
by|Dec 28, 2020
A: Yes, each pull comes with two screws.
by|Nov 16, 2022
2 found this answer helpful
Q:I dont want them rust or oxidize and ruin my doors. Thank you
by|Jun 5, 2020
2 Answers
Answer This Question
A: No, these are not recommended for outdoor use.
by|Jun 10, 2020
A: Steve, Thank you for your question. The pull has not been tested for constant contact with water therefore we cannot recommend installing outdoors. Best, Customer Care Team