Q:Can this be combined with "Onward 3-1/4 in. (82 mm) Brushed Nickel Pocket Door Pull with Privacy Lock" so that they lock together on a converging/double sliding door?
by|Apr 17, 2024
1 Answer
Answer This Question
A: Hello,
Thank you for your inquiry. This product has not been tested in such an application.
Best Regards,
by|Apr 18, 2024
Q:What is the depth measurement of the flat recessed finger inset?
by|Aug 22, 2021
1 Answer
Answer This Question
A: Hello,
Thank you for your interest in our product. The depth of the finger recess is 6 mm (1/4 in).
Best regards,
Customer Care Team
by|Aug 24, 2021
Q:Will this work on a door that is 1-3/4" thick?
by|Nov 28, 2020
1 Answer
Answer This Question
A: Hello,
It's for door thickness 1 1/4'' to 1 1/2'' (31.8 mm* to 38.1mm*).
Thank you.
by|Oct 15, 2023
1 found this answer helpful
Q:Does this come with a metal piece for the door jam like the locking ones do?
by|Nov 15, 2020
2 Answers
Answer This Question
A: Hello. No, the passage are pulls only, and do not have a jamb plate. The privacy pulls have a jamb plate to allow locking. Thank you
by|Nov 16, 2020
A: No. The version I purchased had just the pulls. I believe they do make a "privacy" version that would likely have them though.
by|Dec 4, 2020
Q:We need a pocket door pull 3and 1/4 inches by 1 and 3/4 inches, but our installer said it can be larger because he said he could cut out more of the door to fit in the pull. Will this pocket door pull fit the bill? We need enough of these pulls for three pocket doors. Thank you
by|Oct 15, 2020
1 Answer
Answer This Question
A: Hello. The dimensions of the cut out required in the door to accept the pocket door pull are 2-7/8 inch. high (73 mm) x 1-3/4 inch. wide (45mm). The pocket door pull itself is larger (3-7/32 in x 2-9/32 in) than the cut out needed so the cut out is not visible. Check our guide here : https://www.richelieu.com/documents/docsGr/119/400/6/1194006/1411883.pdf
I hope this clarifies. Thank you
by|Oct 15, 2020
Q:what are the measurements of this lock
by|Mar 14, 2020
2 Answers
Answer This Question
A: Hello Susan. Pocket door pull height is 3-1/4 in. (82 mm), width is 2-1/4 in. (58 mm). Requires a door thickness between 1-1/4 in. (32 mm) to 1-1/2 in. (38 mm). I hope this clarifies. Best Regards
by|Jun 21, 2020
1 found this answer helpful
A: The measurements of this lock are
Cross bore diameter (in.)
2.28
Product Depth (in.)
1.75
Product Height (in.)
3.23
Product Width (in.)
2.28
Required door thickness (in.)
1 3/8
Strike height (in.)
1.25
Strike width (in.)
.25
Throw length (in.)
0.25
by|Mar 16, 2020
Q:Can it be used on a hollow door?
by|Aug 12, 2019
2 Answers
Answer This Question
A: Hello. Yes, no problem. Regards. Customer Care Team.
by|Jun 27, 2022
1 found this answer helpful
A: Wouldn't recommend it. The second mount screw is set relatively close to the edge of the required cutout and might not give enough shoulder strength for continuous use.
by|Jun 27, 2022
1 found this answer helpful
Q:Could you please tell me the dimensions? Thanks.
by|Jun 27, 2019
2 Answers
Answer This Question
A: Hello. The pocket door pull dimensions are : Height of 3-7/32 inch. (82 mm) and Width of 2-9/32 inch. (58 mm). Please see the following document : https://www.richelieu.com/documents/docsGr/119/400/6/1194006/1445881_hd.jpg
Be careful, the dimensions of the cut out required in the door to accept the pocket door pull are 7/8 inch. high (73 mm) x 1-3/4 inch. wide (45mm). The pocket door pull itself is larger than the cut out needed so the cut out is not visible. Please look at the instructions here : https://www.richelieu.com/documents/docsGr/119/400/6/1194006/1411883.pdf
I hope this helps. Please feel free to contact us again if you need more assistance. Best Regards. Customer Care Team.
by|Jun 28, 2019
A: The dimensions are 1.75", 3.23", and 2.28" (DxHxW).