Questions and Answers for USG Sheetrock Brand 3/8 in. x 4 ft. x 8 ft. Drywall

A:  Hi Danp. Thank you for shopping at The Home Depot. According to the information on our web page, the price is per piece. If you purchase 44 or more, the price is reduced to $12.96 per piece. https://www.homedepot.com/p/USG-Sheetrock-Brand-3-8-in-x-4-ft-x-8-ft-Drywall-14109012208/100321594 Please let us know if we can be of further assistance. Rick_HD_OC

A:  Thank you for your inquiry. The price is per individual sheet.

A:  Thank you for your inquiry. USG manufactures Sheetrock Wallboard products. You would need to hire a contractor if you are unable to install it.

A:  No, but it's so very easy to install. I can now.

A:  Bill To better assist you, please contact our HD.com customer service department at 800-430-3376 between 6 a.m. and 2 p.m. EST. They can either answer your question or transfer you to your local store to answer your specific question. You can also choose to call your local store directly.

A:  buy a sheet and cut it in half

A:  Yes.  Search for green board.  It cost about $2 more per sheet.  

A:  Thank you for your inquiry. Sheetrock Mold Tough gypsum panels are mold and moisture resistant. Look for Sheetrock Brand Ultralight Mold Tough panels which are 1/2" thick. Hope this helps.

A:  Dear Valued Home Depot Customer, To better assist you, please contact our HD.com customer service department at 800-430-3376 between 6 a.m. and 2 p.m. EST. They can either answer your question or transfer you to your local store to answer your specific question. You can also choose to call your local store directly.

A:  MSDS information is available directly from the manufacturer. Contact them or check their website. 

A:  Thank you for your inquiry. Current SDS for USG products can be found on usg.com. Enter the product in the search box at the top of the page and press enter. Once you locate your product click on it to get to the product page. Scroll down to get to the SDS near the bottom of the page. Thanks for choosing USG products.

A:  You can access the MSDS information on the USG web site under technical information. 

A:  Yes, follow the weight guide on the package. Mike

A:  Thank you for your inquiry. Sheetrock panels are not structural. Any accessories should be attached through the panel to the studs for support. Hope this helps.

A:  Randy To better assist you, please contact our HD.com customer service department at 800-430-3376 between 6 a.m. and 2 p.m. EST. They can either answer your question or transfer you to your local store to answer your specific question. You can also choose to call your local store directly.

A:  Mark USG Sheetrock is sold by the individual full sheet. Hope this helps.

A:  Assuming your walls are 8' high, 15 sheets are the minimum number required to cover your walls. I calculated this by adding the footage of each wall together (equals 57'), then add the inches together (equals 21") and divide by 4' (14.25 sheets for the footage and 1/2 sheet for the inches). If the height of the walls are over 8' then this calculation will be too few.

A:  The amount of Sheetrock you need depends on the height of the walls. Multiply the height times the length of each wall to get the area of each wall. Add the areas of all the walls together. Divide the total of all walls and the ceiling by the area of the board (4' x 8' = 32') to get the number of panels you need. Hope this helps

A:  Sheetrock is 4 feet by 8 feet. If your walls are 8 feet tall, that means your first wall will need 4 sheets, the second one will need 3 and an inch, so 3 sheets and get the leftover from the first wall, same with the third wall (so we are up to 10 sheets) and the last wall will require 5 sheets, for a total of 15. But, that is the ideal, so order an extra for mistakes and whatnot. I would order two extra, but I'm over cautious and don't like going back to the store for just one sheet, one extra would be fine most likely. If your walls are taller than 8 feet, then you have to adjust accordingly, 9 foot walls would require four extra sheets (1 foot by 8 foot strips and you need 15 of these, you can get 4 from each sheet.) Since sheetrock gets taped and spackled, there's not much waste like there is with lumber or tile.