Customer Reviews for Everbilt 1/2 in. Zinc Flat Washer (50-Pack)

I ordered 1/2” washers and received sliding door hangers, ups tracking number 1Z2W46510346760248

Used these as shims for holding a fence post next to a house

Great for the purpose that I was going to use them for...crafts!

Website says washers have outside diameter of 5/8 inch, but the ones I received have OD of 3/4 inch (please see pic).

These washers are spec'd as .75" O.D. on the Home Depot website. They are actually 1.0" diameter. I can't use these for their intended purpose.

This is the most amazing flat washer ever. Its roundness and flatness has changed my life or the better. Not only that l, my wife's life has also been positively affected by its superb qualities.

Worked fine on lag bolts for 6x6 pressure treated lumber used to make a guardrail along my driveway.

Works as intended. Used under nuts for anchor bolts

This washer is two inches outside diameter and point eighty four inches or twenty one millimeter inside. The thickness of the plate is 3 millimeters thick. If you need to stack them you can get 80 millimeter in height or right at three and quarter inch in height. ASC is stamped on the face of the plate on one side of each of the twenty five contained in the brown box they come in. Heavy Duty.

The 5/8 inch zinc-plated cut washer in the 25 pack is of good quality. It is 1 - 5/8 inches wide with a 5/8 hole. It will work for many applications of wood, plastic and metal. The thickness of the washer is 1/8 inch and can be used in a spacing application if necessary to fill needed room. The quality of the manufacturing process seems adequate and produces and consistent product.

Being used for decking or fence building is only one of the multiple uses that these washers are perfect for. The Everbilt ¾ inch Zinc plated cut washer provides a large bearing surface so that when used on softer wood, yellow pine which most of your pressure treated wood is made from, it prevents the fastener from being buried into the wood leaving a week or loose joint. The washer comes in 25 pieces to a box, has a 2” outside with a ¾” inside diameter, is 1/8” thick and is zinc plated making it perfect for outside use. The washer does have some weight and I have used it for other things such as a makeshift plumb bob, weight for a picnic table cloth, replacement calk line hook and a weight for the bottom of my curtains to keep them straight. Good product, recommended.

3/4 inch Zinc Plated Washers. Actual dimensions are 7/8 inch ID and 2 inch OD. About 1/8 inch thick. These washers are steel with a zinc coating for corrosion protection and are brighter than washers that have a galvanized coating. The package contains 25 washers. All washers appear to be consistent in size. Typical use is for 3/4 inch bolts which are used in heavy duty construction like a deck support. But can also be used for craft projects and to add weight to something.

Zinc-Plated 5/8 inch large Washers These large Zinc-Plated washers are nearly 1 3/4 inches in diameter with an inside hole just over 5/8”. They are nearly 1/8 inch thick. These are heavy, smooth, good quality, and nicely zinc plated, making them great for outdoor use like with deck bolts or fence construction. I am quite pleased with these washers.

The Everbilt 5/8" zinc plated cut washers have multiple uses. Not only do they work to prevent a bolt or screw from pulling through material. I use them as spacers to move something away from a wall. Recently I had an odd size metric bolt that was too long. I added enough washers to essentially shorten the bolt as this special bolt would be hard to replace. They can be painted or coated to prevent rusting.

These galvanized flat washer are excellent for my outdoor post. I used these flat washer outside so they are galvanized to prevent corrosion. Made of durable steel they are strong. Twenty five pieces per bag is a good price for half inch hole flat washers. Outside diameter is 1-3/8 inches. They are a little bigger than the size of a US quarter. Easy to use on any project.

The specifications state that the outside diameter is 1 3/8", the inside hole is 1/2", and the thickness is .109". I measured the outside diameter at exactly 1 3/8" , the inside hole at .57", and the thickness at .097". When these measurements were checked across the entire washer there was minimal deviation measured in low thousands of an inch. I did get 25 washers in the bag. The galvanized finish is smooth and even. I actually got these for my wife to use a weights for her weaving projects. To that end, each washer weighs 15 grams or about 0.5 oz. These are made in China.

Galvanized washers have many uses, but mostly to resist rusting in the environment in which they are installed. I frequently use galvanized washers for repairs on galvanized windmill towers and I occasionally use them for and on wooden deck repairs. These 1/2 inch flat washers do what they are designed to do . They are a good product that I expect to last.

1/2 Inch Galvanized Flat Washers. 25 washer per pack. These washers have a dull appearance due to the galvanized coating. If you need something shiny I'd get stainless steel washers. The OD is 1 3/8 inch, the ID about 9/16" and is about 3/32" thick. The galvanized coating gives you corrosion protection. The washers look pretty consistent. Good price.

I needed a couple of these to lag together a piece of wood so my gate had something solid to close against. The washers weren’t exactly right for the lag bolt I used (1/4”x3-1/2”). It seemed like the hole was a little too big but they were close enough. They did bend when I applied a lot of pressure to the lag bolts. Hopefully, they will last a long time.

Great product, good price. Ordered online got when needed.

I love these washers! They are shiny and just the right size for my application. The best part of the purchase was that I was able to select the exact quantity that I needed, rather than having to pay extra for a box of washers I will likely never use.

Not much to say .

Good product. Recommend.

It is a hot dipped galvanized washer.

The washers were thin and they bent when tightened.