Customer Reviews for QEP 10 in. Diamond Blade for Wet Tile Saws for Ceramic Tile

Rating provided by a verified purchaser

Used it on my grinder to cut porcelain tile. Worked great

works fine

Cut like a champ

chipped my tile while cutting - I will have to replace one of my tiles - I will be returning this blade to store - old blade cut 100 percent better than this one

very good and easy to use.

I have used these blades for a long time on hand grinders as dry blades.. I would rather buy 10 $5 dollars blades vs 1 $50 blade, especially if someone drops and bends the blade..its easier to kiss five bucks to the trash, instead of throwing out 50 bucks. And they work great..too bad they are not a stock store item.

not good on marble or granite ok on softer tile

Works great on ceranic tile...not so good on glass pencil tiles. Lots of chips but did the job.

I barely cut 25 tiles when the tiles started cracking. I switched to a new blade and the tile cutting went smoothly until once again, about 25 tiles when the tiles started cracking. Is $20 a good deal? NO!

Very chip and useful tool I appreciate ,And fast delivery

I Just tiled the Bathroom floor and used the Diamond Blades in my Ryobi tile cutter for the first time. They performed like a more expensive blade and I would recommend these blades to anyone. For the price and performance, they are the best blades I have used.

For my small job it worked great. I used it to cut stone tile and ceramic tiles

I purchased 2 blades to work on my bathroom wall and floor ceramic tiles. I used cheap 50 dollar wet saw to cut over 30 feet of tiles. I was very surprised how good it cuts, long as you feed the tiles in consistent slow timely manner. It cut the tiles with no chips. I only had one bad tile at the end of a project, I highly recommend it to anyone for small projects, for bigger projects least buy more blades.

The blade worked really good, we just had problems with the arbor spacer/reducer. We went to the MK Diamond blade that didn't have the arbor reducer and it cut just as well at the same price.

The blade worked better then expected!! Great Buy!! Would purchase this product again if needed.

I used this with my 4" grinder and it worked great. I had to add a washer to ensure it was tight in the arbor. I wanted to cut some tile in the bathroom to get at the shower valve and it was like cutting butter.

Product was installed in the old fixture works great.

cut ceramic floor tiles. Totaled some 4' cut length to date. Very good so far, at a low price.

Great Price & value & quality. Easy installing. Good.

I bought the blade to go on my 4 inch grinder to cut ceramic tile. It worked like I hoped it would. mainly used to cut out holes for the electric plugs and switches

Good least expensive diamond blade cut tile well xx

Couldn't get this in store so I had to order it online. It was expensive to have delivered same day, but it worked well and it cut beautifully my new bathroom tiles.

this blade was horrible causing so much chipping while cutting the ceramic tile. Also the arbor piece came off so after one cut the blade was useless. Waste of my money.

I needed to cut a granite countertop. It performed perfectly. What more can I say about a $5 blade.

This blade cuts well, is easy to handle and is long lasting. We tiled two bathrooms and it performed flawlessly both cutting straight and toilet holes. Get this blade and the round diamond hole saw prior to starting a tile job, it will save time and money. This blade saved many tiles that the scribing cutter didn't cut correctly. Home depot should keep these in stock on the shelves.

This blade is replacing one that I have used for several projects and was "worn to the bone". I replaced it from another supplier and it wobbled which resulted in tiles with a ragged edge. This one runs quiet and smooth with no wobble. I hope I get as many years of use from it as I did from the original blade.

I balked at paying 4 times the cost of this item for an apparently similar product in store. Bought 2 just in case. Turns out to have been unnecessary - this baby on a cheap angle grinder zipped right thru about 5 lf of fairly dense tile and shows no sign of wear. I did pop for a special flange HD sells to aid in the use of grinders for this purpose, and that helped I'm sure.

Very good quality. Will recommond to other users for loading a small project.

You get what you pay for. If you have a small project and don't need quality, it will work. I was disapointed and replaced the blade after one use.