Q:What is the threads per inch on this 1/2" x 4" brass pipe fitting? There is nothing in the description that states anything, so it would be great to know for a project.
by|Mar 28, 2024
0 Answer
Answer This Question
Q:Will this support a 2 Gallon Expansion tank vertically?
by|Oct 12, 2023
0 Answer
Answer This Question
Q:Can this used to connect to water meter if not covered with dirt.
by|Aug 1, 2023
0 Answer
Answer This Question
Q:Does the 3 inches refer to the overall length or the un-threaded length?
by|Jun 9, 2023
2 Answers
Answer This Question
A: Generally, on nipple fittings, the length is the overall length.
by|Jun 9, 2023
A: The Everbilt 3/4 in. x 3 in. MIP Brass Nipple Fitting overall length is 3".
by|Jun 9, 2023
Q:MIP is not tapered. So, is it MIP or NPT?
by|Feb 3, 2023
2 Answers
Answer This Question
A: Hello, it is not either or. This mail iron pipe (MIP - actually brass) does use national pipe threads (NPT). It's just not tapered. Both MIP and FIP use NPT. So, they are compatible.
by|Oct 7, 2023
1 found this answer helpful
A: It is a male version of nominal pipe thread also known as MNPT which means Male Nominal Pipe Thread. Additionally, there are several photographs and line drawings on the site to assist in ensuring that the connection being attempted is possible with this item.
by|Oct 28, 2023
Q:Are the threads on the 1/2"x4" brass nipple NPT (tapered) male threads?
by|Feb 19, 2022
1 Answer
Answer This Question
A: The Everbilt 1/2 in. x 4 in. MIP Brass Nipple Fitting has male tapered pipe threads on both ends.
by|Feb 21, 2022
Q:Can this item be screwed to galvanized water pipe?
by|Jan 3, 2022
4 Answers
Answer This Question
A: Yes, the Everbilt 3/4in. x 2in. MIP Brass Nipple Fitting can be used with galvanized piping. Depending on your local codes an additional dielectric union may be required. Please consult a local licensed plumber to verify code compliance for your exact situation.
by|Feb 25, 2024
A: If the threads are NPT then it can be screwed into same size galvanized, however dissimilar metals may cause accelerated corrosion
by|May 7, 2023
A: Junior, Yes. My suggestion would be to make three wraps with Teflon tape AND with plumbers dope.
Good luck!
by|Jan 12, 2023
1 found this answer helpful
A: NO!
by|Jun 8, 2022
1 found this answer helpful
Q:I want to connect a valve to an existing FIP stub which is mounted against a concrete wall where I will not have space to rotate the valve. Are the threads such that I can just rotate the nipple to tighten both stationary ends? Would I need to cut the threads off one end and sweat or sharkbite the other?
by|Apr 17, 2021
3 Answers
Answer This Question
A: No. What you need are two small nipples (one for stub and one for valve) and a union like this to connect the two (which can be tightened without either end rotating):
Model# 80532
Everbilt 3/4 in. FIP Brass Union
https://www.homedepot.com/p/Everbilt-3-4-in-FIP-Brass-Union-80532/316389729
by|Oct 29, 2023
1 found this answer helpful
A: Not being able to see your installation location, I would suggest screwing a copper or brass threaded to sweat style adapter fitting that would then allow you to install a sweat style valve. Remove the valve stem assembly before heating the valve to solder the adapter and copper pipe extension to the valve. Also, apply ample Teflon pipe tape to the male threads.
by|Apr 18, 2021
1 found this answer helpful
A: It is possible to tighten both sides of the 3/4 in. x 3 in. MIP Brass Nipple Fitting at once but it is not recommended because it would be difficult to get both sides tight enough to not leak. We recommend tightening the ends one at a time, so another method would be needed to attach the valve to the pipe nipple if the valve cannot rotate.