1/2 Inch Drive Dual-Direction Micrometer Torque Wrench (40-200 ft-lb)

TEKTON micrometer torque wrenches are designed to instill confidence in the wrench's accuracy and control during operation. They are calibrated to be accurate within ±3% for both clockwise and counterclockwise directions and certified to the ISO standard for the full listed range (20 - 200 in-lb), unlike torque wrenches calibrated to ASME standards, which do not require calibration below 20% of the listed range. The single half-moon pawl maintains 9 teeth engaged with the gear at all times, so it won't skip under stress. The internal components are the same design and construction as all of our 90-tooth ratchets. The 4-degree swing arc reduces the length of travel at the end of the wrench handle between each click. The micrometer scales are laser-marked in bold fonts on the satin-finished handle body, making them easy to read. The collar springs into a locked position that holds your setting and prevents accidental movement during operation. There is no thumb knob to tighten at the end of the handle. A deep, sharp-cut diamond pattern on the surface of the handle creates a coarse texture that won't slip in your hand. The case provides safe transport for the torque wrench and protects it from drops. Each item in the case has its own place and is held securely.The case is made of high-density polyethylene (HDPE), and the latches are polypropylene (PP). Includes a serialized certificate of calibration.

TEKTON micrometer torque wrenches are designed to instill confidence in the wrench's accuracy and control during operation. They are calibrated to be accurate within ±3% for both clockwise and counterclockwise directions and certified to the ISO standard for the full listed range (40 - 300 ft-lb), unlike torque wrenches calibrated to ASME standards, which do not require calibration below 20% of the listed range. The single half-moon pawl maintains 9 teeth engaged with the gear at all times, so it won't skip under stress. The internal components are the same design and construction as all of our 90-tooth ratchets. The 4-degree swing arc reduces the length of travel at the end of the wrench handle between each click. The micrometer scales are laser-marked in bold fonts on the satin-finished handle body, making them easy to read. The collar springs into a locked position that holds your setting and prevents accidental movement during operation. There is no thumb knob to tighten at the end of the handle. A deep, sharp-cut diamond pattern on the surface of the handle creates a coarse texture that won't slip in your hand. The case provides safe transport for the torque wrench and protects it from drops. Each item in the case has its own place and is held securely.The case is made of high-density polyethylene (HDPE), and the latches are polypropylene (PP). Includes a serialized certificate of calibration.

Tekton split beam torque wrenches are quick to set and can be stored at any setting. They are calibrated to be accurate with ±4% for the clockwise direction and are certified to the ISO standard for the full listed range (50 - 250 ft.-lbs.), unlike torque wrenches calibrated to the ASME standards, which do not require calibration below 20% of the listed range. The 90-tooth ratchet has a single half-moon pawl that maintains 10 teeth engaged with the gear at all times, so it won't skip under stress. The 10° flex head offers the clearance to work around nearby obstructions. Some accuracy is lost when the handle is not in the straight position, so this feature should only be used when needed. Every torque wrench includes its own calibration certificate, matched to the serial number on the handle. 5 measurements are recorded at each of the three set points (50, 150, and 250 ft.-lbs.) and the results are printed on the certificate. When a torque spec calls for Nm, you can flip the wrench over and use the conversion chart on the back. The chart is laser-marked as large as possible. The conversion factor is also labeled above the chart if you'd rather do the math (1 Nm = 0.7376 ft.-lbs., rounded to 0.74 on the wrench). The case provides safe transport for the torque wrench and protects it from drops. The case is made of high density polyethylene (HDPE) and the latches are polypropylene (PP). The manual/certificate of calibration packet and reducer are held securely in the case.

Tekton 72-Tooth Split Beam Torque Wrenches are easy to read and easy to set. Quickly turn to the desired torque value with a smooth thumbscrew adjustment. Teeth inside the cover lock the torque setting in place while you are using the wrench. Because there's no internal tension when the wrench is at rest, you don't need to turn it to the lowest setting for storage. Each Tekton Split Beam Torque Wrench is calibrated according to the ASME B107.300-2010 standard. The detailed test results are recorded on the included certificate. The certificate includes the initial accuracy, expected future accuracy, and the wrench's serial number. All torque wrenches lose accuracy with repeated cycles. The expected future accuracy information helps you evaluate when recalibration may be necessary. Each wrench is engraved with a unique serial number that corresponds to its certificate of calibration. The conversion scale on the handle of the torque wrench offers a quick reference for converting ft.-lb to Nm. The handle is made from an impact-resistant nylon with nonslip polypropylene grip. The head of the torque wrench has a 10-degree flex joint, offering clearance to work around nearby obstructions. As with any flex-head torque wrench, some accuracy is lost when the handle is not in the straight position, so this feature should only be used when needed.