#1 Home Improvement Retailer

Internet #204845385

Model #BCSR01

Store SKU #1000037226

Multi Turn Valve Stem Repair Kit

  • Genuine OEM replacement parts
  • Ideal for repairing stem of multi-turn valves
  • Compatible with angle or straight valves
  • See More Details

Frequently Bought Together


Product Overview

Genuine BrassCraft Manufacturing replacement parts. This repair kit is for angle and straight style multi-turn valves. Easy to install.
  • Repairs stem of multi-turn valves
  • Install on angle or straight valves
  • Quick and easy installation
  • Original OEM replacement parts

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.



Maximum compatible pipe size (in.)
Product Depth (in.)
Product Height (in.)
Product Width (in.)


Maintenance, Repair & Supplies Product Type
Miscellaneous Repair Kit
Minimum compatible pipe size (in.)
Pack Size

Warranty / Certifications

Manufacturer Warranty
Limited Manufacturer Warranty. See BrassCraft.com

Questions & Answers


Will this repair kit work with jameco compression valve

Asked by George December 5, 2020

The bibb washer can be pulled off of the repair kit stem and used to get the valve to isolate. I left the packing washer from the Jameco in place because it looked a little different and was if fair condition. The kit packing washer may have worked but I didn't try it. The Jameco handle will not fit on the Brasscraft stem.

Does this kit work for BOB brand? I googled BOB. It looks like they are no longer in business.

Asked by Richard November 17, 2020

I'm not sure but if you only need the rubber washer and packing just check the BOB shaft and rubber washer size and switch just those parts. The kit is only about $3.

Will this work with a Teledyne multi turn shut off valve?

Asked by SA November 5, 2020

SA Thank you for your question. The BCSR01 repair kit is designed to repair the Brasscraft multi turn stop valves. They would not be guaranteed to work for a Teledyne part

I can easily find and replace the front seal rubber in front of the stem, but my problem is comin...

Asked by Larry July 23, 2020

This should work...depending on the exact valve I'm working on, I sometimes use the whole kit, and sometimes just a few of the parts....on some valves, it's better to reuse/refit the old stem with these new washers.....pay attention to the assembly order shown on the package.....And, it's a cheap kit....try it....!

How do you pull the old metal stem Unscrew or tap out?

Asked by Thom April 1, 2020

Unscrew it. It may require a little pulling to get it out after unscrewing, and check to see if the old stem-end washer is left behind in the valve.

Will this work on a Watts valve?

Asked by me February 6, 2020

Hello-No, the BCSR01 is designed to work with our BrassCraft multi-turns. We would not recommend it being used inside another manufactures stop. If you have any questions, please contact our Customer Support Team at 877-272-7755.

Will this repair kit work for a BrassCraft "1/2 in. Nom Comp Inlet x 3/8 in. O.D. Comp x 3/8 in. ...

Asked by James September 12, 2019


Are these stems the same length as the old brass stems from way back when, say 1980 when!!! Will ...

Asked by Cippy August 16, 2019

Just installed in a 30 year old valve. Length was the same.

Is the plastic ok to use on a hot water line?

Asked by Mike May 15, 2019


Is there a video instruction on how to use this repair kit on youtube?

Asked by Peter April 23, 2019

I've not looked, but probably there is....it's super-simple......the key is first, shutting the water pressure off at the incoming source or street.... after that, the other key is undoing BOTH the valve shaft and the shaft retainer nut at the same time so they don't jam....the little cap will come off before the valve is totally unscrewed...from there, it should be obvious how to do the repair....hope this helps...!

Multi Turn Valve Stem Repair Kit - page 2

Customer Reviews

  • 4.7
    out of 83 reviews
  • 95% recommend this product
Filter by:
Showing 1-10 of 83 reviews
Great parts
Easy to restore a water valve gasket.. than to replace the whole thing..
by Castro
4 people found this helpful
Easy simple and now saving us huge on h20 bill...
Easy simple and now saving us huge on h20 bill had no idea that some thing so little could break so big old part was just shredded to nothing. We love this part but price is even better thx to This Old House for the TIP........
1 person found this helpful
Worked perfectly
Had older brasscraft valve which was probably the original in one of my bathrooms. Have hard water here so when I shut off the valve to clean my toilet the valve started leaking. Was going to buy another valve until I saw this rebuild kit. Install was so easy- 5 minutes and it worked perfectly. Highly recommend.
by Luv2bike
The bad news is my made in China BrassCraft valve failed at only 6 years old in a way that caused...
The bad news is my made in China BrassCraft valve failed at only 6 years old in a way that caused a huge amount of problems. The rubber "washer" that controls the water flow self destructed and broke into pieces inside the valve. That meant you could no longer shut off the valve AND pieces of the washer went into the kitchen faucet and dishwasher and messed both of those up. So basically a $3 part created a full day of DIY work and what would have been hundreds of dollars in a plumber's time. It required taking apart the single control kitchen faucet and replacing the cartridge valve. It also required removing the dishwasher and and clearing the rubber bits out of the inlet solenoid valve. The only good news is this kit allowed repairing the valve without replacing it. But I would never buy a BrassCraft valve in the first place. BrassCraft is Chinese junk.
by DIYguy
Response from BrassCraft MfgMay 31, 2019
We regret to hear of your experience. It is important to note that the BrassCraft valve installed in your kitchen is Designed, Machined and Assembled in the United States of America. We take great pride in our US manufacturing facilities. The BrassCraft brand has been the professional's choice for more than 70 years because of our quality. That being said, we would like to hear more about your experience. Please give our Customer Support Team a call toll-free at 877-272-7755 and reference this review.
3 people found this helpful
Repair is Easier and Cheaper Than Replacing Everywhere I looked the only answer was to replace th...
Repair is Easier and Cheaper Than Replacing Everywhere I looked the only answer was to replace the valve. The existing valve was in good condition, no corrosion or rust and worked just fine until I turned the water on and off a few times trying to fix a leak. I had no idea what brand of valve but I knew the problem was a bad washer. I did not know how to repair it. Thank goodness for YouTube because HD staff did not suggest the possibility of repair or know about this kit. Common wisdom is-- it is not cost effective to rebuild. The hard to find kit was $3 and saved me a $150 minimum visit from a plumber to replace the valve. My valve is soldered onto a very short piece of copper pipe.To replace the valve myself I'd have to buy a pipe cutter, learn to weld plus buy supplies and a torch to solder more pipe onto the stub. Costs a whole lot more than $3. This repair kit was the cost effective option for me. Had to go to three Home Depots. Call first because inventory check indicated in stock all over town. They were not. Even at the store with the kit in stock I had to ask because I could not find it on the shelves. The kit solved the problem of a toilet water supply valve that would not turn off in order to install new flooring and a new comfort height toilet. The fix was quick and easy, less than 10 minutes. I turned off water to the house, loosened the screw, removed the handle and packing nut, lefty loosied to remove the existing gray stem. Made sure I got all of the damaged washer out. I set the pieces on the floor in the order I took them off. Put the new white stem and washers in. All this trouble caused by a squished and deformed washer. Three days later, the fix held, no leaks! Next visit to HD I will get a couple of washers now that I know the right size. I already have an extra kit. : )
by Angelnot
14 people found this helpful
It worked as designed!...
It worked as designed!
by TClark922
Rating provided by a verified purchaser...
Rating provided by a verified purchaser
by HomeDepotCustomer
Rating provided by a verified purchaser...
Rating provided by a verified purchaser
by HomeDepotCustomer
I had a number of brass shut off valves that...
I had a number of brass shut off valves that would not open. These replacement valve kits were easy to install and now these valves open and close with ease.
Showing 1-10 of 83 reviews