Internet #205611390

Model #RK7323

Blade Runner X2 Portable Tabletop Saw

  • Designed for unlimited capacity for cross and rip cuts
  • Switch between standard t-shank jigsaw blades in 3 seconds
  • Compact, lightweight cuts wood, tile, plastic, metal and aluminum
  • See More Details

Frequently Bought Together


Product Overview

The Rockwell BladeRunner X2 Portable Tabletop Saw is the solution to the problem of having to take materials back to the workshop to cut them, and then bring them back to the job site later on. If you’re a contractor, you know that that process can add an entire day to a project. The BladeRunner is only 15 lbs, so while stable and sturdy, it’s easy to toss in the back of the truck. And with a footprint of only 15.75” x 17”, it doesn’t take up an entire workbench like traditional table saws. The hold-down guard and splitter allow for work with wider materials, and a larger rip fence than other portable table saws provides better control and accurate cuts. A no-load speed of 3000/min, a stroke length of ¾”, with 5.5 amps of power gives it the capacity for light to moderate cutting of wood (up to 1-1/2”), ceramic tile (3/8”), PVC pipe (1-1/4”), aluminum (3/8”), and steel (1/8”). (Anything over 1-1/2” and you’re probably going to need a traditional, permanently fixed tabletop saw—but you can’t take that to the job site.) The blades change out almost instantly, in under 3 seconds once you get the hang of the tool-less blade change system. And the saw is protected by a Rockwell 3-year limited warranty, so you know they stand behind their tools.
  • [SETS UP IN SECONDS] Take this table saw to the job site or move it around the workshop. There’s even a built-in carry handle
  • [CUTS LIKE A FULL-SIZE] With the standard guard and riving knife system you can perform rip, cross, scroll, and miter cuts
  • [TOOL-LESS BLADE CHANGE] Uses any brand’s standard 4” T-shank blade, but we threw 5 in the box to get you started cutting wood, ceramic tile, plastic, aluminum, and metal
  • [0-60° MITER CUTS] With the adjustable gauge you can pull off precise miter cuts for a whole assortment of woodworking projects
  • [ON-BOARD ACCESSORY STORAGE] When the miter gauge, rip fence, and extra blades aren’t in use they can be conveniently housed in the base of the saw
  • [SAFETY SWITCH] Prevents accidental starting, plus the vacuum port lets you hook up a shop vac that cleans while you cut
  • Safety switch with key prevents accidental start

  • Click here for more information on Electronic Recycling Programs
  • California residents

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.

Compare Similar Portable Table Saws

13 Amp 8-1/4 in. Table Saw
current product
Blade Runner X2 Portable Tabletop Saw
15 Amp 10 in. Table Saw with Folding Stand15 Amp 10 in. Expanded Capacity Table Saw With Rolling Stand
Name13 Amp 8-1/4 in. Table SawBlade Runner X2 Portable Tabletop Saw15 Amp 10 in. Table Saw with Folding Stand15 Amp 10 in. Expanded Capacity Table Saw With Rolling Stand
Cordless/ CordedCordedCordedCordedCorded
Rip Capacity - Right12 in612 in27 in
Included AccessoriesAllen Key/Wrench,Anti-Kickback Prawl,Blade Guard System,Blades,Rip FenceBlades,Miter Fence,Rip FenceStandStand
Power Tool FeaturesBlade Guard SystemBlade Guard System,No Tool Blade ChangeBlade Guard System,Stand IncludedBlade Guard System,Stand Included
Cuts ThroughWoodAluminum,PVC,Plastic,Porcelain,WoodWoodWood
Blade Diameter (in.)8-1/441010
Table Tilt Right Max (degrees)4504545
Work Table Surfacein. x x x x in.
Blade LocationCenteredCenteredCenteredCentered
View ProductView ProductView ProductView Product



Blade Diameter
Maximum Cut Depth @ 90 Deg.
Product Depth (in.)
Product Height (in.)
Product Width (in.)
Work Table Surface
in. x in.


Amperage (amps)
Bench & Stationary Tool Type
Table Saw
Blade Diameter (in.)
Blade Location
Blade Speed
Color Family
Construction Material
Acrylonitrile Butadiene Styrene (ABS)
Cord Length (ft.)
Corded Tool Type
Specialty Saw
Cordless/ Corded
Cuts Through
Depth Control
Horsepower (hp)
Included Accessories
Blades,Miter Fence,Rip Fence
Maximum Cut Depth @ 45 Deg.
Power Tool Features
Blade Guard System,No Tool Blade Change
Product Weight (lb.)
PT Horsepower (Hp)
Rip Capacity - Left
Rip Capacity - Right
Table Tilt Left Max (degrees)
Table Tilt Right Max (degrees)
Tools Product Type
Power Tool

Warranty / Certifications

Certifications and Listings
ETL Listed
Manufacturer Warranty
3 years limited

Questions & Answers


Is there an accessory that will extend the fence a few more inches for wider cuts than the width ...

Asked by Jim February 7, 2021

Never seen one. Try making your own, though, with a strip of melamine & some innovation.

Can you use a Dado blade on this saw?

Asked by Yo January 20, 2021

No. Only a standard T-shank 4" jig saw blade.

what size blade does this come with?

Asked by Eddie January 13, 2021

[TOOL-LESS BLADE CHANGE] Uses any brand’s standard 4” T-shank blade. There are 5 included to get you started cutting wood, ceramic tile, plastic, aluminum, and metal

Can this saw cut meat and bone like a butcher saw or band saw

Asked by Adebanjo December 5, 2020

You would ruin it.

Is it made in America?

Asked by Stephen December 1, 2020

No. It is made in China.

Do you have this item available now at store city industry 91745 ? nternet #205611390 Model #RK7323

Asked by Jamie October 21, 2020

Look at the HD website.

how do you put a blade in the saw

Asked by phil October 11, 2020

There is a button on the top surface that you push down and then pull right. It opens a clasp under the red center guard that you insert the blade end into. Once its seated, you release the button and the clasp closes around the blade. Very easy, but I always unplug the unit before doing so.

I am trying to find something to cut 1" squares of balsa wood without the pieces going flying. Wo...

Asked by Rae October 4, 2020

If what your telling me is that your primary concern is how to eliminate pieces from Balsa wood from flying during the cutting process. This item does NOT have a variable speed motor. I would suggest in your case to use a JIG SAW because they do have a HIGH & LOW speed. Low speed I believe is the only way you can stop the pieces from flying while your cutting. However, this unit is equipped with a SUCTION HOSE fitting where you can attach a hose from a "wet/dry vac. If you like this item, that is what I would do to catch the pieces.

Has anyone used this saw to cut tile. I'm not expecting miracles and I only have probably 4 cuts ...

Asked by Pete June 25, 2020

It might be possible. Use a squirt bottle and a proper blade. Go slow. I have not tried it but I would use water to try. Tilt water way too.


Asked by rick May 15, 2020

I'm sure you can cut crosscut laminate flooring with the Rockwell Blade Runner just not with the guide as you cannot fit it on the top of the unit. You would have to guide it by hand which is not difficult. Just make sure you use the correct blade and take your time. I have cut 1/4" aluminum with this saw and it does a pretty solid job. I use it for many things and I love it.

Blade Runner X2 Portable Tabletop Saw - page 2

Customer Reviews

  • 4.2
    out of 685 reviews
  • 84% recommend this product
Filter by:
Showing 1-10 of 685 reviews
Seriously, don't waste your money on one of these.
This thing is a piece of debris I wish I had never bought. Good luck getting a square cut with this junk. The guides are useless. The T-Square supplied is not even close to accurate and because of all the plastic involved, fexes in ways that throws work out of alignment and not square. I hate this thing and will most likely try to get $20 for it at a flea market or something. I should have just bought a $20 hand held jig saw and a table saw. I had it sitting around the shop too long to return or I would. I'll NEVER BUY ANOTHER Rockwell tool again.
by TomInHollyHillFL
Response from Rockwell Tools ExpertMay 21, 2020
Hey Tom! Thank you for sharing your honest review. We hate that this has occurred while using your tool, but the Bladerunner saw should be simple to use and effective for precise wood crafting. So that we may further assist you with this matter, please call our Solution Center at 866-514-7625.

Thank you for choosing Rockwell! rockwelltools
9 people found this helpful
This is one tough little saw! of course, this shouldn't be the only one saw for all your needs, i...
This is one tough little saw! of course, this shouldn't be the only one saw for all your needs, if you're up to big projects, but one you shouldn't be without; it's so easy to use and gets the job done; add a miter saw for cutting thicker woods such as 2x4s and you're all set. Highly recommended.
by Berg
6 people found this helpful
I read the reviews before purchasing and was skeptical, but for the price I was willing to take a...
I read the reviews before purchasing and was skeptical, but for the price I was willing to take a chance. I am impressed, now take into consideration I'm a hobbyist on a small scale. I make wooden and plastic toys for kids and this meets my needs. I'm not going to frame a house with it or even use it to install base moulding but it does allow me to precut larger material for use in my cnc router. it has plenty of power, light weight, does not take up much space and requires no tools to use. I do recommend taking the time to adjust the blade roller bearing guides and the parallel alignment of blade to table. I checked the fence measurement scale with the side profile of blade and it is right-on. If you can get this table saw for a good price, buy it.
by Setek
5 people found this helpful
A light weight workhorse
The BladeRunner X2 is such an important and unique tool to me that after buying and using one for four full days of work, I purchased a second one as a backup. For me the ability to have a table top saw that can cut so many different materials which is less than 15 lbs making it so easy to transport is a game changer. I no longer need to transport a 45 lb plus jobsite table saw around. Although it is light in weight, it has been a true workhorse for me. I have used it regularly for almost a year and a half for big and small jobs. From rebuilding two sheds, to making a slop sink surround, ripping plywood, cutting trim boards, PT lumber, ceramic tile, and wood flooring, etc, this light weight wonder has never let me down. While I own two of them, other than as an extra saw for my workshop at home, the first BladeRunner X2 has done the bulk of the work and is still going strong. I depend on my BladeRunner X2 so much that I do not know how I would accomplish my work so efficiently without one.
by GuitarMan
excelent if you dont need to big work
excelent if you dont need to big work
by Sebafal
4 people found this helpful
Product is great, simple and quick assembly of a few knobs. A lot of thought went into designing ...
Product is great, simple and quick assembly of a few knobs. A lot of thought went into designing this product. It also comes with a variety pack of 5 blades to get you cutting the same day. I am very happy with my purchase, this saw is now one of my most used tools. I did not give it five starts because when using the included fence I could not get straight cuts, the blade likes to wonder to one side. Also the vacuum port at the top works great but I wish there was one below as a lot of sawdust falls down under the machine and then I clean it up with a vac.
by Lycan004
Response from Rockwell Tools ExpertMay 7, 2018
Thank you for taking the time to share your feedback! rockwelltools
9 people found this helpful
Hello Rockwell & public...I'm Travis & I purchased this saw after seeing the commercial...Wow this little saw is the truth!!!...light weight and its like scribing with a pencil...smooth cuts & very reliable...only draw back to me is I wish they add a light near the cutting area & add rubber feet so it want move while cutting. One more thing would be nice is to high light the table scale...more visible to set your fence by....overall I really love this saw. *( pics are my partner Eric in action )*
by ShortCut
Awesome product
[This review was collected as part of a promotion.] My wife knew I had been wanting the BladeRunner for awhile so she surprised me with one for Christmas and the day after Christmas I made a little table for it so I could clamp it in the Jawstand XP or Jawhorse Sheetmaster that she got for me last Christmas. I just finished my first project with it a bridge for a Ho scale train layout made of 1/4" poplar Square stock and was able to do all the cutting in the house thanks to the shop-vac hookup on the saw. I would definitely recommend the BladeRunner I have cut just about everything with it except tile and I don't have any complaints with it.
by KamikazeXJ
I bought this saw for my nephew to build things. He has used it several times and loves it. He sa...
I bought this saw for my nephew to build things. He has used it several times and loves it. He said he wished it would raise up higher to cut larger pieces of wood. I love the handle hole and it is lightweight for me to carry. Thanks for making a great product under $100. Here are photos of the planter that my nephew made using your saw in September 2017. He hopes to build and sell these raised planters and your $1,000 would really help.
by cindyfreland
Response from Rockwell Tools ExpertOct 18, 2017
Hello Cindy,
Thank you for taking the time to share your experience and review! We greatly appreciate your feedback. Love the raised planter by the way, it looks AWESOME! rockwelltools
4 people found this helpful
I use this on trim work and anything that uses 3/4 inch wood and works great. I even ripped 8ft ...
I use this on trim work and anything that uses 3/4 inch wood and works great. I even ripped 8ft boards with this multiple times. Would a table saw be better? Duh. But for the price and small space this takes up its worth it once you get how to hold the board down. And anyone that has said the fence moves must not know how to screw the knobs down. My latest project was my entertainment center in the picture.
by BZ
Response from Rockwell Tools ExpertNov 21, 2017
Hello Valued customer,
Thank you for taking the time to share your review! We greatly appreciate your feedback. rockwelltools
33 people found this helpful
Showing 1-10 of 685 reviews