TNFP System 200 Kit Low GWP Spray Foam Sealant Insulation

Thank you for posting your inquiry. Unfortunately, your inquiry does not contain enough background/detail to provide a proper reply in this format. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information from you, to permit us to better address your question.

Thank you for your inquiry and for your interest in the DAP Touch ‘n Foam Professional Low GWP Foam Kit 200. While it is possible to use this product for the application as described, filling or applying product overhead can be challenging. Please be sure to use proper PPE (Personal Protective Equipment) and to tarp/protect the work area (in the event that foam drips from the application site). Be sure to conduct a test application prior to proceeding, to ensure that your application technique is producing the desired results. When filing overhead, it is recommended to apply multiple thin layers, rather than one large application, this minimizes waste and facilitates a complete fill and full cure. Should you wish to discuss your intended project or have any additional questions, please feel free to reach out to DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for your inquiry and for your interest in the DAP Touch ‘n Foam products. As indicated on the product literature, the Touch ‘n Foam Pro System 200 kit provides an ASTM C518 Aged R-Value of up to 6.2 per inch (when properly applied). As per building code, low pressure two component spray foams are only approved for installation at a maximum thickness of 2 inches (51 mm). Should you have any additional questions or require further assistance, please feel free to contact DAP’s Technical Customer Service Department at 888-327-8477

Thank you for your inquiry and for your interest in the DAP Touch ‘n Foam products. In theory, the project that you propose is possible, however, please be sure to measure/monitor your substrate surface temperature, as it is very common for uninsulated metal surfaces to be dramatically hotter/colder than the air temperature in the application area. Surface temperatures should be measured with a non-contact IR/laser thermometer to ensure that you apply the foam within recommended temperature range. The use of spray foams in overhead applications can be challenging. Please be sure to use proper PPE (Personal Protective Equipment) and to tarp/protect the work area (in the event that foam drips from the application site). Be sure to conduct a test application prior to proceeding, to ensure that your application technique is producing the desired results. When filing overhead, it is recommended to apply multiple thin layers, rather than one large application, this minimizes waste and facilitates a complete fill and full cure. Be sure to verify compliance with your applicable local codes before proceeding. Should you wish to discuss your intended project or have any additional questions, please feel free to reach out to DAP’s Technical Customer Service Department at 888-327-8477.Should you have additional questions, please feel free to contact DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for posting your inquiry on the DAP Touch ‘n Foam Professional Low GWP Foam Kit 200. When fully cured this product will have a firm/rigid texture. Should you have any questions or require further assistance, please feel free to contact DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for posting your inquiry on Touch ‘n Foam Pro System 200 Kit. DAP Touch ‘n Foam Pro System 200 Kit provides up to 200 board feet of polyurethane spray foam (200 sq. ft. @ 1" thickness). Should you have any additional questions or require further assistance, please feel free to contact DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for your inquiry and for your interest in the DAP Touch ‘n Foam Professional Low GWP Foam Kit 600. The inquiry that you have posted does not contain enough background or detail to allow us to provide a proper response in this format. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain this information from you, and to permit us to properly answer your question.

Yes, absolutely. Spray foam is one of the most efficient ways to insulate in new construction

Thank you for posting your inquiry and for your interest in the DAP Touch ‘n Foam products. DAP Touch ‘n Foam Professional Low GWP Foam Kit 600 1.75 PCF FR ICC dispenses a low pressure, two-component closed cell polyurethane foam product that is tested and documented per ASTM D6226 to achieve 90%+ Closed Cell Content. Should you have any questions or require further assistance, please feel free to contact DAP’s Technical Customer Service Department at 888-327-8477.