The AvantiPRO 7 in. Turbo Diamond Blade provides the best cutting performance and long life for all of your DIY projects. Use the turbo rim blade for fast and smooth cuts on concrete, brick, block, stone, and stucco. This blade will fit most 7 in. angle grinders and circular saws.
Turbo rim
Ideal for cutting concrete, brick, block, stone, and stucco
Did the job. Had multiple paver cuts for a septic...
Did the job. Had multiple paver cuts for a septic tank / riser lid. Made the job much easier. Would purchase again.
by
Verified Purchase
Jan 18, 2022
Cuts Stone Like Butter
I used this blade to cut Hanover Chapel Wall blocks that are 6" thick and 9" wide using a standard woodworking circular saw. Set the saw depth about 1/4" deep and cut all 4 sides of your block, then increase the depth and cut again. Repeat until you have either cut the stone completely through or reach the maximum cutting depth. I used a wide piece of steel plate as a cold chisel and was able to separate the two pieces of the block with a few light taps.
by
Verified Purchase
1 found this review helpful
Sep 15, 2020
Cheap made
This diamond blade I my father in law just bought this blade and not even one bricks I cut and the center ring came out so I won't buy it again
by
Jul 25, 2020
Saved me a $150 asphalt saw rental!
I was skeptical. Cutting asphalt with a circular saw. Ended up cutting 2 approx 14x14 holes in my asphalt drive to put posts in for a gate. Asphalt was anywhere from 2-3” thick. Ran a slow stream of water on the pavement where I was cutting, plugged the saw into a gfci receptacle (in case water got where it wasn’t supposed to while sawing) and kept the cord well away from the water. Worked slow, but as someone said, deliberate, and it cut like butter. Used a 7 1/4 Ryobi 15 amp regular circular saw, put the front edge of the shoe on the pavement, pulled the trigger and moved the blade guard up out of the way and did a slow plunge cut, then pushed it like you’d cut anything, kept just enough pressure forward to let the saw work, but didn’t force it. Hit the corners with a thin wide chisel... and the pieces came right out. Had the depth set to about 2 1/2”, never hit dirt or rock with the blade.
Great blade for small stuff.
Saw a couple comments about the arbor spacer in the middle. It’s brass, and mine came out, but I tapped it back in place gently with a finish nail hammer and was gentle putting the blade on the saw, and had no problem.
If you cannot figure out how to do that... you probably don’t need to be cutting asphalt.
by
Recommended
7 found this review helpful
Jun 18, 2020
This saw blade did the job I purchased it for,100%
This saw blade did the job I purchased it for,100%
by
Verified Purchase
Recommended
Jun 4, 2020
Great blade, don't belive the bad reviews.
Used this blade to cut a ton of concrete pavers that were 2.5" thick. I was worried about the purchase because the reviews stated the arbor would pop off and the blade would not be secure. I used the blade in a 12amp 7.25" Skillsaw with no problems. Because of the dust I did run a trickle of water from my hose to help repress the dust. I have included pictures of the blade prior to all the cuts.
by
Recommended
3 found this review helpful
Jun 3, 2020
Cuts through the cement stone retaining wall with no problem.
Cuts through the cement stone retaining wall with no problem.
by
Verified Purchase
Recommended
Jun 2, 2020
Did not last long. The first foot was great the remaining 6 feet were horrible metal was actually...
Did not last long. The first foot was great the remaining 6 feet were horrible metal was actually coming off the blade. I would love to return it.
by
Verified Purchase
1 found this review helpful
Jun 2, 2020
Wall Cap Cutting
I used this on a circular saw for cutting wall cap for planter boxes i built. The blade cut very nice crisp lines especially on my corner pieces that matched up perfect
by
Recommended
2 found this review helpful
Apr 28, 2020
Great tool for cutting hardy backer board. A must...
Great tool for cutting hardy backer board. A must for your tool box.