Non-Marring Vise Jaw Accessory for Use on Vises with Jaws from 3 in. to 6 in. Wide

A:  Soft rubber. Works great.

A:  This accessory is 6" and attaches magnetically. So it fits your 5" vice. I use it for my 4" and works perfect. You can center it or if needed, place the edge flush with the vice jaws. Very useful.

A:  This is one size fits all. They are about 5 1/2" long and the magnets on the back are set apart 3", so that's why the description says 3-6 inches. My vise is 5", so these hang over the ends (ever so slightly) which doesn't interfere with anything I've done.

A:  Dave, this set can be used on a 3 to 6 inch vise jaw. So your 5 inch will work these just right.

A:  The jaws on my vise are 6-inches wide. The Non-Marring inserts that I received are 5-1/2 inches wide. They should work fine, or you can cut 1/4-inch from each side.

A:  The product is 5.5 actual inches. There may be a little overhang on youre vise jaws depending on the width of youre vice. Not a problem. It still does the job.

A:  These fit all my vises...a 3" & 4" drill press vise & a bench vise.

A:  This item only comes 5 1/2" wide. It will work on VISES that are 3 to 6 inches wide.

A:  They are 5 1/2'' wide

A:  Actual width of the pads is 5-1/2". I use them on a 4" vise, just let them overhang each side. Rather than cutting them to fit, I shift them left or right as needed to utilize the various molded-in angled grip channels. The magnets on the jaw-side (2 per pad) are each about 1-1/4" left & right of center, so there's plenty of leeway to move the pads as any given use may necessitate.

A:  The overall length of the non-marring vise jaw is 5 1/2 inches. The dimension to the outer edges of magnets (silver spots in photo) are approximately 3".

A:  The angled groove is 1/4": the four straight grooves are 1/16" , 3/32", 5/32 and 9/16."

A:  The available dimensions are Elliptical end, 90-deg - 3/8, Center, 90-deg - 1/4, Left & right of center, 90-deg - 3/32, Round end, 45-deg - 3/8, Horizontal - 15/64.

A:  Face-to-face, uncompressed, using standard drill bits as a gauge, here's what I came up with: Elliptical end, 90-deg - 3/8" Center, 90-deg - 1/4" Left & right of center, 90-deg - 3/32" Round end, 45-deg - 3/8" Horizontal - 15/64"

A:  The 60 degree angled holds a 3/8'' drill bit one vertical holds a 1/8'' bit next one 1/4'' then 3/32'' and 3/4'' . middle cross hole 15/64'' I have used the jaws on many projects and they are well worth the money { one angled four vertical and one horizontal grooves }

A:  There are 6 grooves, 1st. Approx. 3/16" round running the length horizontally. 2nd, Approx. 5/8" round 90 degrees to top surface, 3rd. 1/4" round 90 degrees to top surface, 4th. 1/8" round 90 degrees to top surface, 5th. 1/16" round 90 degrees to top surface, 6th. 3/8" round appears to be at a 15 degree angle to top surface running from outside down toward center. I hope this helps you.

A:  Grooves are about 1/4 inch width

A:  They will hold a small 1/4 inch and larger. The product is made from a very durable but very soft so it will really hold various sizes. So if you want to hold something smaller than 1/4 just place it in the center of the non groove section and it will hold it just fine.

A:  Rough diameters with jaws face to face: Horizontal groove - 1/4"; angled - 3/8"; center verticals - 1/8",1/4", and 3/32"; end vertical is not round, rather 3/8"deep X 5/8" wide

A:  1/16, 1/8, 3/16, 1/4, 5/8,

A:  There is one angled groove and 3 various size straight grooves

A:  Hi Chuck, The Bessey jaws are sold as a pair. You will receive 2 jaws for the $10.73 cost. Joe

A:  Pair.

A:  You get a pair, both with embedded magnets so they don't fall off the vise jaws..

A:  mine came as a pair

A:  Sold as a pair. Work great when you need firm but non-maring pressure.