10.1 oz. Latex Window Glazing

It was a little to soft, but I made it work.

WORST product Ive purchased in Decades...Sorry, but this tubed window glazing was POOR. Its too wet [like pudding] and difficult to work with any tools. I had to fight with it to get it to lay down properly. I would NEVER purchase this product Ever Again.

Remember the first time you used 100% silicone caulk? I bet you made a mess. But after awhile you got the hang of it and would never go back to water based. It's the same with this type of glazing. It takes practice to get good at it but once you do it's not too bad. Yeah, the tub glazing is more user friendly but the downside is you have to wait a month+ for it to skin over to paint. This stuff only takes a few days to dry and can be painted with latex paint. Put water on putty knife to smooth.

I waited until the end of fall to paint my windows, just to see the glazing (probably original, 1978 build) half cracking away. I intended to buy regular glazing compound, but I couldn't wait the 2 months it can take for traditional compound to skin over for paint before it would already be freezing outside. I saw this, and figured being water based it would skin over faster. Because it skins over faster, it'll probably dry through and start cracking faster too, but it's a compromise I made due to starting the project so late in the year. I read a lot of reviews, most of them being negative, but here's what I did and it seems fine. I chiseled the old stuff out, pulled out the points, and pulled the glass out. I then chiseled some more and sanded everything with 120 grit because that's what I had. I primed the window frame with kilz original primer. It's oil based. I did this because at that point I still thought I was going to used the regular dap 33 glazing compound. You can probably use water based primer with this, so long as you paint over with water based paint. I left it to dry for about a day. Now for glazing: I used the angled tip to fill a 45 where the window would seat. I was pretty generous with the caulking. All the excess will ooze out, and you'll be able to scrape it or cut it with a razor blade later. I laid the glass in, and pressed the sides down. Make sure everywhere you can see around the window has compressed caulking to make sure the whole face of the frame is sealed. If it's not, pull the glass up and add more caulking. Press in some glazing points. My windows are 32x24, and I used 4 on the long sides and 3 on the short sides. I probably went over-kill, 2 per side closer the corners is probably fine. After this, I used the gun sideways to make a large 45 because my windows sit pretty deep. I held the gun up a little bit, and was careful to apply a steady, oversized 45. Even still, it doesn't actually matter how well you apply it, so long as there is more than is needed laid down. I then grabbed my putty knife. The only one I have is a 6" knife, and it worked fine. I wet the edge, set it in the corner, and dragged it straight to make the 45 degree edge. This takes some skill to do straight, especially in the corners. You have to scoop out the excess, without pressing the knife into the 45 you want to keep. Just try it. Keep your knife wet. If you mess up, just add more material. The water helps keep it from drying out on you, if you drag the knife without it being wet it'll drag dry streaks and it won't look smooth. After that, use a knife or the putty knife to scrape the excess. You can wait for the caulking to dry before doing this. If you wait, you'll have less risk of messing up the glazing, but it'll take more work to scrape the dry caulking. I use a blade to cut a straight line along the glass to glazing edge before razor blading the glass up to that line. I let this set in my basement for 3 weeks. I only planned on a week, but was busy. I think DAP recommends 2 weeks if it's freezing out. I painted the exterior side of the window with exterior paint, and painted the interior side with interior paint. It's been installed for 2 months now, and it looks great. All in all, this process requires you to be a little quicker than you would have to be with regular glazing, so it's arguably harder to get an equivalent result. If you do it correctly however, you can install the window much sooner than you could had you used regular glazing. Good luck!

I purchased this for an exterior French door, and it was a nightmare to work with! Also the product hardened within a few days. I do not recommend this product.

This stuff was like cake icing. I thought it’s be like using caulk but it was 100x thinner. Took me hours to do just a few window panes. Then it started running by the end of the day. Not made for high humidity areas. If that wasn’t bad enough, just a couple of months later & it’s FULL of mold, coming apart & still not completely dry in couple of places!

I used this latex glazing to do a project that requires glazing a LOT of windows. It took some getting used to, but was faster than standard glazing once I had practice. I was excited to not paint all those panes. HOWEVER, in less than a year, the caulk "melted" off the panes with exposure to rain. This happensed on both the window that I glazed and did not paint (as the instructions say you can) and the windows I glazed and then later painted.

An awful product. Don't make the mistake I made in assuming that this is the same stuff that comes in the small tub that you normally use to glaze glass in a window frame. It's not. Apparently, to get it to come out of a tube, it contains a solvent to thin it. Apparently, that solvent begins to dry out immediately. The result is that, by 15 minutes or so, it surface hardens and you cannot smooth it out; it just pills up into an ugly mess that you can't even get off a window frame without stripping. Imagine how it would be to try to smooth out fast dry acrylic latex caulk after 20 minutes--that is what you have here (see my attached picture). I have glazed many many windows, so I'm not just a weekend DYIer. In the case shown in the picture, I was not even fully glazing a window glass--I was using this stuff to set the glass on an old exterior door. It still made a mess because it began to dry before I could turn the door over and smooth out the overflow. Why did I buy it in the first place? I saw it used on the TV show "This Old House" a week ago and my old tub of DAP had dried out. So much for their product placement. I have used many DAP products and think they are very good. This one needs to be changed. I will never buy it again.

Much harder to work with than the original, oil based glazing compound