AWG 3-Bar Window guard in White

Rose, I have seen that application. Thank You, Grisham Bros.

Jacob, NY Dept of Health Grisham window guard approval number as follows: HDWG:07-20-01 Stamped on the vertical stiles of each window guard. Thank You, Grisham Bros.

abcd, Not sure I fully understand your application with the wood shutters. The window guards are designed to be positioned within the window jamb on a double hung window. Thank You, Grisham Bros.

Actually the correct application is to install the window guard unit within the windows outer channel on a double hung window. Helpful link provided: https://www.google.com/search?q=How+to+install+a+window+guard+in+NY+city&sca_esv=3d5ed972a4208e78&sca_upv=1&rlz=1C1VDKB_enUS1112US1112&sxsrf=ADLYWIIvJix30FVrOYGrGMF8oKka9sqCFw%3A1727226888825&ei=CGTzZq2DMq6GptQP-O6C6Qw&ved=0ahUKEwitp57J9dyIAxUug4kEHXi3IM0Q4dUDCBA&uact=5&oq=How+to+install+a+window+guard+in+NY+city&gs_lp=Egxnd3Mtd2l6LXNlcnAiKEhvdyB0byBpbnN0YWxsIGEgd2luZG93IGd1YXJkIGluIE5ZIGNpdHkyBRAhGKABMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRirAkil3QFQrwpYvc8BcAF4AJABAJgBqAKgAbFBqgEHNTEuMzAuMrgBA8gBAPgBAZgCHaAC5xjCAgoQABiwAxjWBBhHwgIHECMYsAIYJ8ICCBAAGIAEGKIEwgIIEAAYogQYiQXCAgQQIRgKwgIHECEYoAEYCsICBRAhGJ8FmAMAiAYBkAYIkgcHMTMuMTUuMaAHp88C&sclient=gws-wiz-serp#fpstate=ive&vld=cid:1ea0277b,vid:7MCYpf409SE,st:0 Hope this helps.

hhh, Not available in 19" inches wide. Units start at 22-3/4 wide. Thank You, Grisham Bros.

Richard, The I.D opening size is too small by 2-1/4" inches. You would not be able to mount within the frame. Not sure you have limitations to mount externally? Thank You, Grisham Bros.

Salvatore, The Grisham Window guards have extension limitations not to exceed beyond 38-1/2" to meet coded deflection ratings. If the application is for security reasons, then perhaps window bars should be considered. Hope this helps. Thank You, Grisham Bros.

Jersigr17, Certified by NY City Dept of Health which requires that the AWG units be permanently installed. (No Pivoting for Egress). Check the Jersey code, but pretty sure they abide by the NY City Code. City of Newark, NJ window guard code. Hope the below helps. 1. General Installation Requirements. (a) Window guards shall be installed in accordance with all applicable requirements of the State Uniform Construction Code, N.J.A.C. 5:23, and with manufacturer's instructions. (b) Any window guard installed on an emergency egress window shall be releasable or removable from the inside without use of a key, tool, or excessive force. An emergency egress window is any window in a sleeping room located on the second or third floor, other than a window providing access to a fire escape. (c) Any window guard installed on a window that is not an emergency egress window, including any window in a unit located above the third floor and any window in a room on the second or third floor that is not a sleeping room, shall be designed, constructed and installed so that it cannot be removed, opened or dislodged without the use of a key or tool. 2. Specifications for Window Guards. (a) Window guards shall be so constructed as to reject the passage of a solid four inch sphere at every space and interval. (b) Window guards shall bear a 150 pound load at a centerspan when extended to maximum width. (c) Window guards shall be constructed of metal or of other material of comparable strength and durability. In order to avoid obstruction of light and air, the diameter or width of metal rods used in window guards shall not exceed 1/2 inch. (d) Window guards shall be designed, constructed and installed so as to serve their intended protective purpose without any risk of collapse, breakage, spreading of the bars or other malfunction. (e) In a room, window guards shall be of at least a height sufficient to allow a total openable window area, for all windows in the room, of not less than 4% of the floor area of the room. In a public hallway, window guards shall protect the full openable area of each window. (f) Window guards shall be securely fastened in order to bear the required load. (g) All window guards shall be so designed and installed as to prevent the lower window from being raised four inches or more above the lowest section of the top horizontal bar of the window guard. Where necessary, rigid metal stops shall be installed securely in the upper tracks of each side of the bottom window. (h) Screws used to mount window guards and stopping devices should be: (1) Minimum Size No. 10 and long enough to penetrate one inch into a wooden window frame; or (2) Of an adequate type, size, and length to be securely fastened to a metal window frame. (i) The coating of window guards shall be unleaded. (j) Window guards shall be installed only in sound (non-rotting) mountings or tracks. (k) Window guards installed prior to the passage of this section shall be accepted as being in conformity with the specifications contained in this paragraph d,2 if they were installed in accordance with paragraph d,1 above. 3. Additional Specifications for Window Guards Other than Double Hung Windows. (a) Window guards intended for casements, sliders and other types or combinations of windows in which the height of the openings is not subject to limitation, shall be of such size as to fill the entire aperture, and shall reject passage of a solid four inch sphere at every space or interval. (b) Except as otherwise provided in paragraph (c) below, sliding windows and vertical pivoting windows may be equipped with stopping devices in place of window guards as follows: (1) For sliding windows, solid metal blocks, measuring at least 1/2 the depth of the window track and 1/2 the width, shall be securely fastened into the bottom and upper window tracks to prevent the window from opening four inches or more. (2) For vertical pivoting windows, metal stopping devices shall be securely fastened to the upper and lower window frames so as to prevent the window from pivoting open four inches or more. The height of the stopping devices shall extend not less than one inch nor more than two inches beyond the window frame as needed to stop the window. The protruding edge of the stopping device shall be smooth and rounded. (c) Use of such stopping devices in lieu of window guards shall be allowed within dwelling units only where they do not preclude meeting the requirement, as per N.J.A.C. 5:10-16.2, that the total openable window and/or openable skylight area in each room be equal to at least 4% of the floor area of the room. e. Penalty. Anyone found to be in violation of this section shall be subject to a fine not to exceed $1,000, or to imprisonment for a term not to exceed 90 days, or both Thank You, Grisham Bros.

Need to correct the information given. I am one of the oldest child guard manufacturers in NY of approved child guards since the 80's. NYC regulations are slightly different than NY regulations such as the guards must be non openable or removeable unless.