4 in. HOLE DOZER Bi-Metal Hole Saw with 3/8 in. Arbor and Pilot Bit
$31.97
Pay $6.97 after $25 OFF your total qualifying purchase upon opening a new card. 
Apply for a Home Depot Consumer Card- Most Durable Hole Saw. Period.
- New 3.5 TPI Tooth Design
- All- Access Slots for Fast Plug Removal
- View More Details
Free & Easy Returns In Store or Online
Return this item within 90 days of purchase. Read Return Policy
Product Details
Specifications
Questions & Answers
139Questions
Q:Can I switch out the included Milwaukee 3/8 arbor and pilot bit for the Milwaukee 1/4 arbor and pilot bit?
by|Dec 8, 2023
1 Answer
Q:Will this cut Stainless steel
by|Dec 6, 2023
1 Answer
Q:Will this work for brick?
by|Sep 28, 2023
1 Answer
Q:Will this work for pottery?
by|Sep 2, 2023
1 Answer
Showing 1-4 of 139
5
2453
4
441
3
114
2
116
1
275
Nov 19, 2023
works great
I had to fill a door hole with a piece of wood. Used a 2x4 and it was very easy to use, that piece was cleanly cut and now that hole is gone! Ill use it again when finished making a new door for an odd sized hall closet. Very pleased! Thank you.
by
Nov 14, 2023
Worst hole saw I have ever used.
Wouldn’t cut through 3/4” subfloor. Even with the lightest amount of pressure and the lowest torque setting possible, it kept buckling, and eventually fried my drill. I can’t believe I spent $50 on this thing for it to ruin my drill and set me back half a day. What an expensive mistake. Do not buy.
by
Response from Milwaukee ToolNov 22, 2023
We'd like to hear more about your experience. Could you email us at social.media!@milwaukeetool.com? Thank you! - The Social Team
Sep 21, 2023
Recommend!
Worked great for my pegboard project! I would usually go for an inch but i wanted a wider grip for training
by
Sep 7, 2023
Great Deck Board Remover
With deck screws buried in the wood I would have to chip away to get to the head, then hope I don't strip the head or even the screw bit, and then hope the screw rises instead of spinning in place. With this hole saw I first sawed a pilot hole in a small 2x4, then removed the drill bit (3mm hex key), then use the 2x4 with the pilot hole to get an initial saw cut around the deck screws without the saw wandering, then finish sawing until reaching the required depth. Boards come right off.
by
Aug 30, 2023
Did the job of cutting a hole in metal! I installed an Easystart device on my AC system, and I needed to drill a hole for the strain relief fitting.
by
Aug 23, 2023
Bought a repurposed mango-wood cabinet to use as an entertainment center - unfortunately, there were no holes for the component plugs. Picked this up at a local Home Depot and it worked like a charm - cut right through the hard wood and made a nice clean cut!
by
Jun 6, 2023
Garbage product
Total waste of money, only lasted 3 holes before the teeth on the bit were gone. Product says it's rated for plaster and drywall, but that's a lie. I had to go back and purchase a hole saw with carbine teeth which worked like a charm. So if your looking to buy this hole saw for plaster/drywall, save your money and go with one that has carbine teeth. Basically wasted $35 and an hour of my time.
by
Response from Milwaukee ToolJun 8, 2023
Thank you for taking the time to review your Milwaukee 4 in. HOLE DOZER Bi-Metal Hole Saw with 3/8 in. Arbor and Pilot Bit and we are sorry to hear about your experience. Could you send our team an email at Social.media@milwaukeetool.com, so we can assist? Thank you - Milwaukee Tool, Social Team
Feb 1, 2023
It Works Ok.
Bought this to drill a whole in a butcher block countertop. It did the job but took longer than it should have. I was using it with a Milwaukee M18 Fuel drill so no lack of power. Just cut slowly and left burn marks all inside the hole. Also looks like it could split along the weld. Not impressed for it being made by Milwaukee.
by
Oct 13, 2022
Great tool
Tool is sharp, cut right through the metal. Made 12 holes, and the bit worked perfectly without any issues.
by
Oct 13, 2022
Incredible hole cutter
I had to make 8 holes in 3/16 plate. I looked at sevaral option and this hole cutter was by far the least expensive. The results were incredible. It cut through this steel like butter. The cutter is still sharp after 8 holes. I am very impressed
by
0/0
