#1 Home Improvement Retailer

Internet #100054132

Model #920924

Store SKU #920924

T&G Oriented Strand Board (Common: 23/32 in. x 4 ft. x 8 ft.; Actual: 0.703 in. x 47.75 in. x 95.75 in.)

  • T&G profile allows for fast and easy installation
  • Meets or exceeds PS2 standards
  • APA rated subfloor panel
  • See More Details

Product Overview

OSB is a material with high mechanical properties that make it particularly suitable for load-bearing applications in construction. The most common uses are as sheathing in walls, flooring, and roof decking. Product may vary by store.

Specifications

Dimensions

Actual Product Length (in.)
95.875
Actual Product Thickness (in.)
0.703
Actual Product Width (in.)
47.875
Nominal Product Length (ft.)
8
Nominal Product Thickness (in.)
23/32
Nominal Product Width (ft.)
4

Details

Engineered Wood Type
OSB/Waferboard
Plywood Features
None
Span Rating
24 OC
Weather Exposure
Exposure 1

Warranty / Certifications

Manufacturer Warranty
See store for details

Questions & Answers

133Questions30Answers

what is a good wood to use for roofing over a porch

Asked by paul May 12, 2021
2
Answers

This OSB is a good sheathing for roofs. Just make sure your joists are spaced properly and you cover the OSB properly with felt paper or appropriate underlayment and then your flashing and shingles. good luck with your project.

how many board will i need for 4x8 shed

Asked by roy May 11, 2021
3
Answers

Not enough information to answer your question. Sheathing just the exterior of the walls, the interior or both? Do you need sheathing for the roof? How tall is your shed? if for the exterior is 4x8 the outer most dims? Lets assume you're sheathing the exterior fo the walls and t's 4'x8' for the outer most dims and the height is 8' for each wall. that means you'll need one sheet for each 4'Wx8'H wall and two for the 8'W x 8'H back wall. You'll then also need another two for the front wall, depending on cutouts for doors, windows, etc. No you're looking at roughly 6 sheets to do the outer side of the walls. if you need them for the roof then you'll need more depending on the dims of your roof. If the outer dims of the walls are even slightly over 4'W and 8'W, or taller than 8' high you'll need to compensate for the extra area. What about the floor area? Do you need some for the floor? To determine how many sheets you'll need for your project just measure and calculate the square feet needed and then divide by 32 (that's the sf of one sheet of this OSB) to get the number of sheet needed. If you get an odd number then round up (since you can't buy 8.3 sheets, if that's what your calculation comes out to be, it means you'll need 9 sheets, for example). Good luck with your project.

can this be attached to asphalt underneath?

Asked by deltatango February 25, 2021
4
Answers

Probably not very well. Asphalt isn't as dense as concrete and the fasteners you use and may, over time, loosen up and move. You might look into an adhesive of some kind to glue your substraight down. Home Depot has many options in store and on line.

can I use this for roof decking?

Asked by leisa February 7, 2021
2
Answers

Yes it can. I used it for sub flooring but it can also be used for roof decking. I would give a word to the wise, T&G (tongue and groove) can be challenging to line up and may pose a danger on a roof. Be careful.

Can this be used for a condo balcony if coated with waterproofing?

Asked by Cliff January 13, 2021
5
Answers

I would use it as a subflooring. I don't think a waterproofing coating would be sufficient for the wear and ear a balcony would endure. Weather would immediately exploit any wear points and degrade the OSB.

What is the weight of the sheet?

Asked by 19 November 17, 2020
2
Answers

I never put one on a scale but to me they are pretty light. I can carry 2 at a time easily if the wind isn't blowing!

Can you paint this using battle ship grey polyurethane paint? Thanks

Asked by Rog November 11, 2020
3
Answers

yes you sure can do that.

Is the TG on 2 sides of the sheet? Meaning, 1 side of the width, and 1 on the length.

Asked by Eric September 19, 2020
3
Answers

T&G are only on the length

Can i use adhesive to glue doen engineered hardwood flooring on this subfloor?

Asked by Mac August 29, 2020
2
Answers

I'm using liquid nail and don't anticipate any future problems with swelling from the glue.

is this exterior rated

Asked by six August 9, 2020
4
Answers

I do not know. I checked the piece left over and did not see "exterior" written anywhere on it..

T&G Oriented Strand Board (Common: 23/32 in. x 4 ft. x 8 ft.; Actual: 0.703 in. x 47.75 in. x 95.75 in.) - page 2

Customer Reviews

  • 4.3
    out of 376 reviews
  • 80% recommend this product
Filter by:
Showing 1-10 of 376 reviews
Easy to install!!
I bought these for a base that I built for a storage shed on my property. After framing out the subfloor I laid these boards down. They have a track that you line the boards up with and it creates a nice flat surface. I then used red guard to water proof the plywood Easy to cut and install.
by Young
It falls a little short
Im putting together a she shed floor 12x16. I bought the tongue and groove to make stronger connections and not have to put in nailers every four foot. The floor is also insulated. I did not see at the store that each sheet is 1/4in. less in width. When I installed the three sheets to make up the 12 ft end I was over an inch short. Who in their right mind makes or sells such a product when construction is in feet increments. So be prepared to make a filler strip or be one of those guys that says it'll be covered.
by Angrybuilder
15 people found this helpful
Good sheeting to build floor
Good sheeting to build floor
by gotheatedup
1 person found this helpful
Easy to put together and was great for the job
Easy to put together and was great for the job
by FROGS2401
1 person found this helpful
We are using the OSB boards for sub flooring. It is sufficient for what it is being used for.
We are using the OSB boards for sub flooring. It is sufficient for what it is being used for.
by GG
1 person found this helpful
Easy to work with. Very strong.
Easy to work with. Very strong.
by Mitchythekid
Worked out great as underlayment for the Neocon Show at Merchandise Mart.
Worked out great as underlayment for the Neocon Show at Merchandise Mart.
by DissapointedMikeinLockpor
2 people found this helpful
Solid for the most part. Some of the tongues were broken off and the sales associate disappeared,...
Solid for the most part. Some of the tongues were broken off and the sales associate disappeared, so we had to load 20 sheets by hand instead of watching him lift them for us. We needed the board so we did not complain or fuss. We used it as temporary flooring to get on the roof, then used it as roof decking. The rest we plan to use as flooring.
by
1 person found this helpful
The OSB was surprisingly better grade than used to be provided for flooring. It was easy to handl...
The OSB was surprisingly better grade than used to be provided for flooring. It was easy to handle and cut to size when needed. The tongue and groove joints went together easily, even with the use of liquid nails in the joints. The project I had was to replace the sub-flooring in two large rooms in a double wide mobile home after the roof was left to decay and leak for over two years.
by Robbie
16 people found this helpful
not 4' wide installed as instructed, and too many surface defects
for nearly $30/sheet, you'd think it would be a better product or that you'd have choice of a better one. I needed to use this for the flooring (subfloor) in my shed. I don't intend to floor over it but looks like I'll have no choice. First, less than 50% of the sheets I pulled were free "enough" of surface defects to use. Second, the short edges are indeed 8' apart, but the measurement from the tip of the tongue to the groove edge is just 4'. That means if you put the tongue ANY bit inside the neighboring groove (as designed), it will fall short of 4'. Therefore, you will run short of your sheathing/flooring calculation. I had to scab my 20' building with about a 2" rip just to finish it off and that was with pretty generous 1/4" gaps on the T&G edges. Short edges (4') are typical. 8' edges aren't. Just be aware. Straight edge sand ply fits as you expect.
by Rsqdivr
15 people found this helpful
Showing 1-10 of 376 reviews