640 oz. Board Polyurethane 2-Component Spray Foam Sealant Kit

Thank you for posting your feedback. We're sorry to see your low star review on the Touch ‘n Foam Pro System 200 Kit. The texture/consistency issues that you describe can result from the product being dispensed out of temperature range and/or in in an "off-ratio" manner (the blend of A and B components out of specification). The application of off-ratio product can lead to poor foam structure (low expansion, weak/brittle, too soft/poor hardness etc.) The most common reasons for this condition are attempting to spray through valves that are not opened equally. As indicating in the product usage instructions: “Fully open valves on both cylinders by turning counter-clockwise until a slight resistance is felt” and/or attempting to apply the chemical through a restricted/partially clogged nozzle: "If spraying has stopped for more than 30 seconds, foam in the nozzle will begin to cure and clog, and system performance will be compromised". To verify that the chemicals are being applied in proper ratio, we recommend a "test application" prior to actual use: Spray a small amount of foam on scrap material to check chemical mix. The foam should be off-white in color and be tack free within 30–60 seconds." Lastly, Troubleshooting: If cured foam appears either lighter or darker in color immediately after spraying, one component may be blocked or empty. Immediately stop spraying and do the following: 1. Check both valves to be sure they are fully open.2. Look for and fix any kinks in the hoses.3. Remove the nozzle, clean off any residual liquid or foam. Check to be sure two roughly equal chemical streams exit the foam applicator barrel by dispensing into a waste receptacle.4. Verify that the chemical, ambient, and substrate temperatures are within the suggested ranges.5. For additional assistance, contact DAP’s Technical Customer Service Department at 888-327-8477. All of the above-referenced information can be found in the enclosed product usage instructions, as well as website usage videos. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information from you and to provide you with additional trouble shooting guidance.

Thank you for posting your feedback. We're sorry to hear about your experience with Touch ‘n Foam Pro System 200 Kit. Based on your commentary, it would appear that you may have been attempting to spray through a restricted/partially clogged nozzle/gun. As indicated in the product usage instructions and website usage videos, "If spraying has stopped for more than 30 seconds, foam in the nozzle will begin to cure and clog, and system performance will be compromised". Likewise as indicated under the Troubleshooting section: “If cured foam appears either lighter or darker in color immediately after spraying, one component may be blocked or empty. Immediately stop spraying and do the following: 1. Check both valves to be sure they are fully open. 2. Look for and fix any kinks in the hoses. 3. Remove the nozzle, clean off any residual liquid or foam. Check to be sure two roughly equal chemical streams exit the foam applicator barrel by dispensing into a waste receptacle. 4. Verify that the chemical, ambient, and substrate temperatures are within the suggested ranges. 5. For additional assistance, contact DAP’s Technical Customer Service Department at 888-327-8477.” Of note, the use of any accessory item (such as chemical lines, application guns, nozzle tips) not specific to this kit can lead to significant performance concerns, as these components are not interchangeable. Should you wish to discuss this with us, please feel free to reach out to DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for posting your feedback. We're sorry to see your low star review on the DAP Touch ‘n Foam Pro System 200 Kit. As with all two-components kits, coverage is expressed as a board foot, this is defined as 12” x 12” square by 1” thick. A System 200 Kit is designed to provide 200 board feet (theoretical output) when properly applied. Even small variations in application conditions (chemical temperature, air temperature application surface temperature), application technique and/or the depth/thickness of applied foam can significantly impact the product's coverage rate. Because you did not provide sufficient background details, it is difficult to provide a more detailed response to your claim of insufficient coverage in this format. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information from you.

Thank you for posting your feedback. The review that you posted (under the DAP Touch 'n Foam System 600 Spray Foam Kit) appears to be for a different product. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information from you and to verify the actual (correct) item that you are attempting to post a review on. When calling in, please have the foam kit available, as we will need to collect model number (UPC Number) and production information (Lot Numbers) from it.

Thank you for posting your feedback on the DAP Touch 'n Foam Pro System 600 Kit. These kits are filled with sufficient material to dispense a minimum of 600 board feet worth of delivered foam (when properly applied). After achieving a full evacuation of the 600+ board feet of delivered foam, there will always be residual chemical in one or both tanks. This condition is normal and expected. Should you wish to discuss this with us, please feel free to reach out to DAP’s Technical Customer Service Department at 888-327-8477.

Thank you for posting your feedback. We're sorry to hear about your experience with Touch ‘n Foam Pro System 600 Kit. Based on your commentary regarding the "leaking" that you describe, it is like that the hose line was not properly connected. The most common causes for this condition are cross-threading, not applying sufficient torque to ensure a seal and/or over-torqueing, which can crush the fitting: "Tighten hose fittings with wrench provided. Do not overtighten". The texture/consistency issues that you describe can result from the product was being dispensed in an "off-ratio" manner (the blend of A and B components out of specification. The application of off-ratio product can lead to poor foam structure (low expansion, weak/brittle, too soft/poor hardness etc.) The most common reasons for this condition are attempting to spray through valves that are not opened equally: “Fully open valves on both cylinders by turning counter-clockwise until a slight resistance is felt” and/or attempting to apply the chemical through a restricted/partially clogged nozzle: "If spraying has stopped for more than 30 seconds, foam in the nozzle will begin to cure and clog, and system performance will be compromised". To verify that the chemicals are being applied in proper ratio, we recommend a "test application" prior to actual use: Spray a small amount of foam on scrap material to check chemical mix. The foam should be off-white in color and be tack free within 30–60 seconds." Lastly, Troubleshooting: If cured foam appears either lighter or darker in color immediately after spraying, one component may be blocked or empty. Immediately stop spraying and do the following:1. Check both valves to be sure they are fully open.2. Look for and fix any kinks in the hoses.3. Remove the nozzle, clean off any residual liquid or foam. Check to be sure two roughly equal chemical streams exit the foam applicator barrel by dispensing into a waste receptacle.4. Verify that the chemical, ambient, and substrate temperatures are within the suggested ranges.5. For additional assistance, contact DAP’s Technical Customer Service Department at 888-327-8477. All of the above-referenced information can be referenced in the enclosed product usage instructions, DVD as well as website usage videos. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information from you and to provide you with additional trouble shooting guidance.tional information from you and to provide you with additional trouble shooting guidance.

Thank you for posting your feedback on the DAP Touch ‘n Foam Pro System 600 Kit. The Touch ‘n Foam Pro System 600 kit provides up to 600 board feet of polyurethane spray foam (600 sq. ft. @ 1" thickness). Even small variations in the depth/thickness of applied foam can significantly impact the product's coverage rate. Because you did not indicate what your application depth/thickness was or provide any background on your application technique, application conditions or project background, it is difficult to provide a proper response in this format. At your convenience, please contact DAP’s Technical Customer Service Department at 888-327-8477 so that we can obtain some additional information regarding your experience.