18 lb. Easy Sand 20 Lightweight Setting-Type Joint Compound
- Joint compound for one-day drywall patching and joint finishing
- Lightweight and offers low shrinkage and superior bond
- 20 minute working time
- View More Details
Ask about this product
Get an answer now with AI
AI-generated from the text of manufacturer documentation. To verify or get additional information, please contact The Home Depot customer service.
Product Details
About This Product
USG Sheetrock Brand Easy Sand 20 Joint Compound is a lightweight, setting-type compound with a 20-minute working time. USG setting-type joint compounds provide faster finishing of drywall interiors, even under slow drying conditions. Rapid chemical hardening and low shrinkage permit same-day finishing and usually next-day decoration. USG Sheetrock Brand Easy Sand 20 Joint Compound features an exceptional bond; virtually unaffected by humidity extremes. It is ideal for laminating double-layer systems, particularly fire-rated assemblies, and for adhering gypsum panels to above-grade concrete surfaces. May also be used for surface texturing and for filling, smoothing and finishing interior above-grade concrete. Note: Setting-type joint compounds should not be used for skim coating due to dryout concerns.
Highlights
- Weigh up to 25% less than conventional weight setting-type joint compounds
- Sands easily; similar to a ready-mixed, all-purpose joint compound
- Unique humidity resistance
- Check-crack resistance in heavy fills
- For interior gypsum panels and exterior gypsum ceiling boards
- GREENGUARD Gold certified for low-emitting performance
- Return Policy
Product Information
Specifications
Coverage Area (sq. ft.): 340
Dimensions
Coverage Area (sq. ft.) | 340 |
|---|
Details
Drywall Features | Lightweight |
|---|---|
Interior/Exterior | Interior |
Product Weight (lb.) | 18 lb |
Set Time (Min.) | 20 |
Questions & Answers
Can durabond 90 be used to plaster over cement board.
Bill- No, joint compound should not be used to "plaster" directly over cement board. Cement board is a substrate for tile. For Dry Untiled Areas—For small areas where the USG Durock® cement board will not be tiled, such as a board extending beyond the tiled area and abutting another surface, treat joints as follows. Seal USG Durock® cement board with Type 1 ceramic tile adhesive. (Mix four parts adhesive with one part water.) Embed USG Sheetrock® Brand joint tape over joints and treat fasteners with USG Sheetrock® Brand Durabond® setting-type joint compound (45 or 90) applied in conventional manner. Flat trowel USG Sheetrock® Brand setting-type joint compound over board to cover fasteners and fill voids to a smooth surface. Finish joints with at least two coats USG Sheetrock® Brand ready-mixed joint compound. Do not apply ready-mixed or setting-type joint compound over unsealed board
How many sq ft per bag joint compound for the skimcoat
Ljcap- USG does not recommend Sheetrock® Brand Easy Sand™ 45 Setting-Type Joint Compound for thin skim coats.
Why does my mud turn hard in 5 minutes? I’m using number 20 but it starts turning hard in in the tray
Tomas Thank you for your inquiry. Easy Sand Setting type joint compound has a shelf life of up to 12 months under good storage conditions. There is a production date stamped on the bag. Be sure the compound you are using is within date. If the bag has gotten damp there could be small bits of hardened compound which act as an accelerator. Similarly, if there is hardened joint compound on your tools or bucket that will also accelerate the set time. Make sure you are thoroughly cleaning your bucket and tools each time you mix a batch. The mixing ratio for Easy Sand setting type joint compound is approximately 1 cup of clean drinkable water for every 3 cups of powder. Make sure you are using clean drinkable water at room temperature. Be sure when you are mixing the compound you are pouring the compound into the water. You do not want to pour water on the to compound.
how much more mud is used for heavy knock down finish
Thank you for your inquiry. USG does not have coverage estimates for using joint compound for texturing, as it can vary depending on how thick it is applied. USG does not recommend using joint compounds for spray applied textures. We offer Tuf-Tex or Sheetrock Wall and Ceiling Spray Texture for knock down finishes.
How l9ng to yiu have to wait before you can sand?
Bryan- The Esay Sand 20 will set in approximately 35 minutes and can be sanded after it has completely dried.
can this be used for large gaps
xxxxxxxx- Gaps greater than 1/8" should be pre-filled with setting-type joint compound like the Easy Sand 45.
I don't want to practice, so how long should I wait (if any time at all) to do the "knock down" on a 8"x8" repair?
Capiz- This time can vary depending on the scope of the project and jobsite conditions. the Easy Sand Setting Type Joint Compound should be completely dry and cured before final decoration.
Can I use this as a skim coat for walls?
Joseph A true skim coat is a very thin application over the entire surface of the wall or ceilings. Easy Sand Joint compound cannot be applied at less than 1/8" over the entire surface of the board. It is not recommended for skim coating.
Viewing 1-8 of 202
Customer Reviews
4.7 out of 5
Loading Recommendations
Related Products
18 lb. Easy Sand 5 Lightweight Setting-Type Joint Compound
USG Sheetrock Brand Easy Sand 5 Joint Compound is a lightweight, setting-type compound with a 5-minute working time. USG setting-type joint compounds provide faster finishing of drywall interiors, even under slow drying conditions. Rapid chemical hardening and low shrinkage permit same-day finishing and usually next-day decoration. USG Sheetrock Brand Easy Sand 5 Joint Compound features an exceptional bond; virtually unaffected by humidity extremes. It is ideal for laminating double-layer systems, particularly fire-rated assemblies, and for adhering gypsum panels to above-grade concrete surfaces. May also be used for surface texturing and for filling, smoothing and finishing interior above-grade concrete. Note: Setting-type joint compounds should not be used for skim coating due to dryout concerns.
18 lb. Easy Sand 45 Lightweight Setting-Type Joint Compound
USG Sheetrock Brand Easy Sand 45 Joint Compound is a lightweight, setting-type compound with a 45-minute working time. USG setting-type joint compounds provide faster finishing of drywall interiors, even under slow drying conditions. Rapid chemical hardening and low shrinkage permit same-day finishing and usually next-day decoration. USG Sheetrock Brand Easy Sand 45 Joint Compound features an exceptional bond; virtually unaffected by humidity extremes. It is ideal for laminating double-layer systems, particularly fire-rated assemblies, and for adhering gypsum panels to above-grade concrete surfaces. May also be used for surface texturing and for filling, smoothing and finishing interior above-grade concrete. Note: Setting-type joint compounds should not be used for skim coating due to dryout concerns.
4.5 gal. Plus 3 Ready-Mixed Joint Compound
Weighing up to 25% less than conventional weight compounds, USG Sheetrock Brand Plus 3 Joint Compound is ideal for repairing cracks on drywall and plaster, embedding USG Sheetrock Brand Paper Joint Tape, and applying drywall filling and finishing coats. May also be used for covering fasteners, USG Sheetrock Brand Corner Bead and Trim, skim coating drywall surfaces, and hand-applying simple textures. Requiring less coats over fasteners and bead, it eliminates the need for taping and topping compounds.USG ready-mixed joint compounds are preferred for consistently high-quality work. Superior formulations are premixed to a creamy, smooth consistency and are essentially free of crater-causing air bubbles. They can be used in hand or machine-tool applications and offer excellent slip, bond, and easy workability.
4.5 gal. UltraLightweight Ready-Mixed Joint Compound
USG Sheetrock Brand UltraLightweight Joint Compound is a ready-mixed, high performance, all purpose compound that offers superior working qualities and good open time. Compared to conventional weight compounds, it weighs up to 40% less, provides enhanced application properties, and is easier to sand. A special formulation makes it ideal for embedding tape and for filling, and leveling and finishing over gypsum panel joints, fasteners, bead, and trim. It's also excellent for skim coating and hand-applying simple textures.USG ready-mixed joint compounds are preferred for consistently high-quality work. Superior formulations are premixed to a creamy, smooth consistency and are essentially free of crater-causing air bubbles. They can be used in hand or machine-tool applications and offer excellent slip, bond, and easy workability.
