Questions and Answers for Aspect Collage 11.75 in. x 6 in. Metal and Composite Peel and Stick Backsplash in Marble Shine (2-Pack)

A:  Thank you for your interest in our Aspect Aged Travertine Peel and Stick Backsplash Tiles! Our tiles can easily be clean with soap and water, or a mild degreaser. We would recommend staying away from any abrasive cleaning agents to maintain the quality of the tiles. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thank you!

A:  Yes, you CAN cut it, but it is somewhat difficult. My friend cut the tip of her finger off doing it :(

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Marble Shine! A chop saw (motorized miter saw) is recommended for straight cuts. A jig saw or scroll saw is recommended for non-straight cuts. For circular cuts, a hole saw works well. See Aspect Tile Installation Guide for additional information. All cutting blades should be carbide-tipped or high-speed steel, and made for cutting nonferrous metal. When cutting is complete, use a fine-grit sandpaper or a small metal file to debur the cut edges. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thanks again!

A:  You can cut it, though it's not terribly easy. I used a jigsaw. I marked my measurements on the back and clamped it down. One problem that happened repeatedly was if the cut was near the edge of one of the little tiles, the piece would break off. I just glued them back in place after puting the cut piece on the wall.

A:  Yes, it can be cut with scissors

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Marble Shine! A chop saw (motorized miter saw) is recommended for straight cuts. A jig saw or scroll saw is recommended for non-straight cuts. For circular cuts, a hole saw works well. See Aspect Tile Installation Guide for additional information. All cutting blades should be carbide-tipped or high-speed steel, and made for cutting nonferrous metal. When cutting is complete, use a fine-grit sandpaper or a small metal file to debur the cut edges. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thanks again!

A:  Yes, you will need cutters for the metal pieces I used QEP 8 in. Rustproof Steel Tile Nipper for Tile up to 1/4 in. 

A:  Yes very easy to cut with a scoring knife or a box cutter... Very easy installation

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Marble Shine! A chop saw (motorized miter saw) is recommended for straight cuts. A jig saw or scroll saw is recommended for non-straight cuts. For circular cuts, a hole saw works well. See Aspect Tile Installation Guide for additional information. All cutting blades should be carbide-tipped or high-speed steel, and made for cutting nonferrous metal. When cutting is complete, use a fine-grit sandpaper or a small metal file to debur the cut edges. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thanks again!

A:  Yes, but only with the right tools. Not scissors or an exact knife. That won't work

A:  Yes you can! Highly recommend! Excellent quality.

A:  Yes, it cuts easily with strong scissors or a box cutter razor.

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Marble Shine! A chop saw (motorized miter saw) is recommended for straight cuts. A jig saw or scroll saw is recommended for non-straight cuts. For circular cuts, a hole saw works well. See Aspect Tile Installation Guide for additional information. All cutting blades should be carbide-tipped or high-speed steel, and made for cutting nonferrous metal. When cutting is complete, use a fine-grit sandpaper or a small metal file to debur the cut edges. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thanks again!

A:  Yes. Use a straight edge and a very sharp utility knife.

A:  The trim you're asking about can accommodate a 4mm tile and the tile is 4.75 mm. Accordingly, i would say yes it would work, though you may have to caulk or grout for a perfect fit. .75mm is a very small difference.

A:  Thank you for your interest in our products! Yes, our Aspect Trim components in Matte White would be a great pairing with our Aspect Collage Peel and Stick Tiles in Marble Shine. If you have any additional questions please feel free to reach out to us at 800.434.3750. Thank you!

A:  I used it for backsplash behind the sink.. So far, it is holding up great. I did not use it behind my cooktop as I had concerns about heat damage.

A:  Thank you for your interest in our Aspect Roman Slab Peel and Stick Backsplash Tiles! Our tiles are rated up to 140 degrees, we recommend they be installed 6" away from a direct heat source; such as a burner. The tiles are fine to install behind a sink as they won't be affected by minimum water exposure. We do not, however, recommend installing them in a wet environment (such as a shower). If you have any additional questions please feel free to reach out to us at 800.434.3750. Thank you!

A:  I installed mine over tile and it came out fine. There?s plenty of stick.

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Oyster! Yes, our our collage tiles can be installed over existing tile. We recommend using our installation method #2 listed on our installation guide, which states to use additional adhesive to secure the panels to your substrate. If you have additional questions please feel free to reach out to us at 800.434.3750. Thanks again!

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Marble Shine! Our tiles can easily be cleaned with soap and water. You'll want to make sure to wipe any spills or splatters as soon as possible to ensure no residue is left behind. If you have any additional questions please feel free to reach out to our customer care team at 800.434.3750. Thank you!

A:  Yes, cooking stains will come off. Just wipe with soap and water or even a mild cleanser. I have mine behind my stove top and I have had no issues. The tile is very wipeable. 

A:  I tried scissors but it didn't work very well so I bought some tin snips and that worked great.

A:  A utility knife. It takes a couple passes. Also works best on very smooth walls but is supper sticky. Good quality for peel and stick.

A:  Thank you for your interest in our Aspect Collage Peel and Stick Backsplash in Cloud Shimmer! A chop saw (motorized miter saw) is recommended for straight cuts. A jig saw or scroll saw is recommended for non-straight cuts. For circular cuts, a hole saw works well. All cutting blades should be carbide-tipped or high-speed steel, and made for cutting nonferrous metal. When cutting is complete, use a fine-grit sandpaper or a small metal file to debur the cut edges. A utility knife with a sharp blade can also be used for straight cuts on the tiles. If you have additional questions please feel free to reach out to us at 800.434.3750. Thank you!

A:  I used a table saw.  Makes a nice straight cut.