Questions and Answers for Kreg K4 Pocket-Hole System

A:  I don't believe there is a screw which would work in thin ply wood. This tool did come with an additional "jig" which I was able to clamp to 3/4 inch and it worked just fine

A:  I have not done that, but I do believe that would be easier. I have not used it with plywood.

A:  I have drilled full 4x8 sheets. I typically leave the sheet laying down & clamp the jig to the sheet & drill.

A:  Take the drill shoe piece off and clamp that to the work piece

A:  They make one for sheet goods that use with a clamp. I have one and very easy to use and works on all plywood thicknesses

A:  Hi Logan, “Thank you for your recent inquiry with The Home Depot.” This link can be used to go to the rebate page. ://www.homedepot.com/p/Kreg-K4-Pocket-Hole-System-K4H/202074960 You will find all the info regarding this rebate on this page. Hope this helps. "We appreciate your business and look forward to serving you in the future.”

A:  No rebate but I purchased mine on sale.

A:  Yes there is a rebate. The online rebate form is the easiest, fastest way to complete your rebate submission.

A:  Thanks for the question. For a limited time, you can save $15 on all Pocket-Hole Jigs over $99 purchased online, at a home center or your local retailer.

A:  All purchases online and in store. Rebate details here on Kreg's website: https://www.kregtool.com/landing/deals-and-promotions.aspx

A:  The jig is designed to work with the bit that is included. The bit pre-drills the hole while creating a shoulder for the screw to sit against, a regular drill bit won’t get the job done. It fits perfectly into the metal lined holes of the jig. You should also be using the manufacturers screws or similar pocket style screw.

A:  Only 1 drill size can be used with this jig.

A:  You need to use the step bit that comes with the kit I believe it is 3/8.

A:  The bit is provided with the jig. It is the maximum size that can be used because the jig has a metal sleeve. The hole accommodates only that sized bit. You will destroy the bushing and affect the life of the jig if you try to use anything bigger.

A:  They make a bit specifically for this jig and it’s one diameter. there is a stop that can be adjusted for different material thicknesses. It’s a great tool once you get use to it . Hopefully this helped

A:  Thanks for the question. Any of the Kreg Pocket-Hole Systems will require the use of the Kreg Stepped Drill Bit.

A:  you must use Kreg drill bit

A:  For this to properly work, you need to use the Kreg specific drill bit because it has a special tip design.

A:  You need to use the special stepped Kreg bit to get a strong glue free joint.

A:  use the kreg bit. they make a pilot hole for the screws and leave material to hold one board to the other. the kit comes with one and you can buy more. I have drilled hundreds of holes and the bit it still sharp

A:  The Kreg K4 Jig will work with a standard 2x4 using the 2 1/2" Kreg Pocket-Hole Screws.

A:  I'm not sure. But I don't see any reason that it wouldn't work. Sorry couldn't help more.

A:  Yes, it will work on a standard 2x4.

A:  It works well with 2 x 4

A:  Yeah, it works well with standard 2x4s. Use the 2-1/2“ blue screws.

A:  You want a coarse screw for this job: https://www.kregtool.com/tool-specs/kreg-screws.aspx

A:  I believe the same screws you would use for joining any type of wood. But you need the screws that are used with this pocket hole system. I would still use wood glue on the joints.

A:  Sorry I do not know what mdf material is.You can buy kits that have different lengths of screws for the K4

A:  https://www.kregtool.com/about-us/news/kreg-tool-tips-joining/match-screws-to-material-hardness.aspx

A:  YOU can use the Kreg screws and I would also glue the joints. I would not trust the screws alone to bond the mdf together.

A:  the kreg course thread screw for soft materials

A:  I would use the course bits. Be careful not to use to much torque because it is easy for the screws to strip out when using MDF.

A:  Use the screws recommended by the manufacturer.

A:  You can use the screws that it comes with, but you should use an adhesive in the hole for a better bond if you are working with mdf

A:  You would use the same pocket hole screws as you would with solid wood. You could actually use any type of screw as long as the screw shaft isn't tapered where it meets the underside of the screw head. You want the underside of the screw head to be perpendicular to the screw shaft. Otherwise you could split the wood or mdf that the screw heads will reside in as you tighten the screws down. I've used pocket holes well over 500 times in building cabinetry and have used them successfully with solid wood, plywood, and particleboard/mdf.

A:  As long as the clamp foot fit in the little pocket on the back, i dont see why not. The only issue you may run into is if the clamp bar sticks up too high, it might get in the way of your drill.

A:  You can use any type of clamp to hold your material square. I personally like to use the automax clamps.

A:  Thank you for the inquiry. You can use a Bar Clamp to hold down the K4.

A:  Sure. As long as it's not too long. I use mine with a C- clamp, because I haven't purchased the Kreg clamps yet.

A:  You can use a adjustable bar clamp as long as it fits the clamp area on the back side of the tool. It’s a round shape.

A:  The kit comes with the base, which has the adjustable clamp and depth gage. It also comes with the drill bit, stopper, Allen wrench for stopper, squarebit driver for screws, vice camp and a multitude of screws in varying sizes. Additionally, you’ll receive a portable single hole guide for tricking spots.

A:  All the hardware

A:  Does todos come complete with everything you need if for a big job you need to buy screws

A:  This product includes the following items: jig, stepped drill bit, 6 inch square driver, screw set, plug set, quick-start guide and 5 project plans.

A:  I bought this a while ago and it works well. The version in store did not come with a full kit. I had to buy it online and pick it up at Home Depot to get the full kit and a lower price then the store version. Overall, I'm happy with it.

A:  no

A:  All the markings in this jig are in inches, you can use it in metric by simply using a caliper and a little of trial and error

A:  I do not know. Contact Kreg.

A:  Millimeter sizes are listed under the inch designation. For example, 2 1/2"=64 mm

A:  Not that I have ever seen.

A:  The K4 does not include the vacuum attachment.

A:  No, it does not come with the vacuum attachment. You can buy it as an add-on. You only get what is in the picture.

A:  No.

A:  Aloha Matt, my K4 did not include a vacuum attachment. Rather than connecting K4 vacuum attachment, I direct jumbo 2 1/2" vacuum hose around K4 after doing several drillings; be careful vacuum will swallow marking pens, screws, wood dust/chips! My K4 used job-specific, not multi-pieces production set-up. My process is: set-up K4 and wood pieces, dry-fit and mark hole locations, drill guide holes, vacuum and put away K4, clamp pieces to jig, glue and screw, vacuum jig (store) and work bench/floor.

A:  No